OPERATORS MANUAL Rev. 7.18.2014 GRAIN CART 1130-20 1131-22 1250-20 1251-22 1500-20 1501-22 J. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 www.jm-inc.
To The Dealer Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration found on the Dealer Portal website located at dealer.jm-inc.com and return it to J. & M. Mfg. Co., Inc. at the address indicated on the form. Warranty claims will be denied if the Warranty Registration has not been submitted. EXPRESS WARRANTY: J. & M. Mfg. Co. Inc.
General Information TO THE OWNER: The purpose of this manual is to assist you in operating and maintaining your grain cart in a safe manner. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance and help maintain safe operating conditions. If this machine is used by an employee or is loaned or rented, make certain that the operator(s), prior to operating: 1. Is instructed in safe and proper use. 2.
Specifications C D SPECIFICATIONS F H A I B E G N WALKING TANDEM DUALS 1130 (20” Auger) 1250 (20” Auger) 1131 (22” Auger) 1251 (22” Auger) Capacity 1,105 Bushels 1,225 Bushels Auger, One Vertical 20” or 22” Diameter 20” or 22” Diameter Unload Time 2.2 or 1.8 minutes 2.5 or 2.1 minutes Wheels 16x42, 18 x 38, 18x42 18x42 Heavy Spindles 4 1/2” Diameter 4 1/2” Diameter Tires 480/80R42, 520/85R38, 520/85R42 or 520/85R42 Tongue Weight Empty 2,900 lbs. 2,900 lbs.
General Information BOLT TORQUE CHART Always tighten hardware to these values unless a different torque or tightening procedure is listed for specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for Metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
Table of Contents 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To The Dealer 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bolt Torque Chart 7-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Rules ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be erased by an operator’s single careless act. In addition, hazard control and accident prevention are dependent upon the awareness, concern, judgment, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
Safety Rules ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged or Missing IMPORTANT: Install new safety signs if #SAFETY Part DECALS # Description the old signs are destroyed, lost, painted 1 JM0018044 Operating Instructions over or cannot be read. When parts are 2 JM0010163 Warning, High Pressure replaced that have safety signs, make 3 JM0014979 Warning, General sure you install a new sign with each new part.
Initial Operation and Maintenance WARNING BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART.
Operating Instructions WHEEL NUTS: Are the wheel nuts properly fastened? Torque to 600 Lbs.-Ft. for standard 22mm wheel studs and nuts. Torque to 500 Lbs.-Ft. for 3/4” wheel studs and nuts. Wheel studs and nuts should be checked after each load during initial operation of the cart and then after every 10 hours of use. Failure to do so may damage wheel studs and nuts. Once the seats are damaged, it will become impossible to keep the lug nuts tight.
Operating Instructions (Continued) 4) Be sure that no debris or foreign objects are in the grain cart. 5) Attach the hydraulic lines to the tractor. Two hydraulic lines (green band) operate the inside gate mechanism. Connect these lines to one service outlet on the tractor. Two hydraulic lines (yellow band) operate the folding mechanism of the auger. Connect these lines to a second service outlet on the tractor.
Lubrication Service Schedule IMPORTANT: Your grain cart has grease fittings at all critical points. These should be serviced before the grain cart is put into operation. WARNING BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART PTO & DRIVELINE: The grease fittings on the PTO should be serviced after every 8 hours of use. Service the grease fittings on each of the drive bearings and also the universal joint after every 8 hours of use.
Trouble Shooting WARNING MAKE SURE THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY QUALIFIED SERVICEMEN ONLY. Trouble... Auger will not return to down position or move from stow position. Hanger Bushing Assembly at the top of the lower auger flighting is hot Possible Cause... Possible Remedy... Dirt In Restrictor (see pg.
Adjusting the Lower Flighting and Hanger Bushing Assembly WARNING MAKE SURE THAT ALL POWER IS SHUT OFF BEFORE ADJUSTING THE FLIGHTING ASSEMBLY. If the drive-dog and hanger assembly are becoming excessively hot during unloading, the lower flighting and/or hanger may need adjusting. The hanger bushing assembly has elongated holes where it attaches to the outer tube assembly. Loosen the two 3/8” bolts on the hanger bushing assembly.
Removing Dirt From The Restrictors On The Hydraulic Cylinder WARNING MAKE SURE THAT ALL POWER IS SHUT OFF AND THE UPPER AUGER TUBE IS IN THE DOWN POSITION BEFORE REMOVING THE RESTRICTORS Remove restrictors from the 90 degree street elbow on the hydraulic cylinder. Remove dirt from the fitting to allow hydraulic oil to flow through the restrictor. Reattach the restrictor to the street elbow. Use teflon sealant tape or equivalent on the threads of the restrictor before reattaching.
Repair Parts List and Diagrams When performing maintenance work, wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing and head. Follow the Operator’s Manual instructions to ensure safe and proper maintenance and repair. Your local, authorized dealer can supply genuine replacement parts. Substitute parts may not meet original equipment specifications and may be dangerous. WARNING MAKE SURE ALL POWER IS SHUT OFF BEFORE PERFORMING ANY MAINTENANCE OR REPAIR WORK.
HUB & SPINDLE ASSEMBLY 250-10 Grain Carts with 6” Diameter Spindles # 1 1 2 3 4 5 6 7 8 8 9 9 10 10 11 12 13 14 15 16 17 Description Hub and Spindle Assembly Complete with 3/4”-16 Studs and Nuts (HSA-1075-34) Hub and Spindle Assembly Complete with 22MM Studs and Nuts (HSA-1075-22) 1”-8 Gr5 Z Centerlock Hex Nut 1”-8 X 8” Gr5 Z Hex Bolt (165450) 6” Spindle - 29-3/4” Long (628) Seal 55179 (Type C) for G250-10,G300-10B, Spring-assisted (CR55179) Large Bearing (71455) Large Race (71750) Hub with studs & nuts (
130 Degree Gearbox Assembly for 22” Diameter Augers (Comer) For Models 1131-22, 1251-22 and 1501-22 Grain Carts # Description Part. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Gearbox Complete (T-325) 2” Output Shaft with 30 Tooth Gear (M56) Double Lip Seal (55X100) Shim (997) Bolt (M10X25) Casing (T325C) Bearing With Race (31307) Shim (677) Oil Fill Plug .
130 Degree Gearbox Assembly For 20” Diameter Augers (SUPERIOR) # Description Part. No.
” Upper & Lower Auger Assembly # Description Part. No.
22” Upper & Lower Auger Assembly # Description Part. No.
Lift Cylinder # Description Part. No. 1 2 3 4 5 6 7 8 9 10 11 12 Hydraulic Hose 1/4” x 160” 1-1/4”-7 Gr5 Z Hex Nut Pac Man Weldment 3” x 24” Welded Cylinder 3/8” female NPT x 3/8” male NPT 90 degree elbow PC-37 Check Valve 3/8” male NPT x 3/8” female NPT swivel; WITH .062 orifice Hydraulic Hose 1/4” x 21” Hydraulic Hose 1/4” x 176” 3/8” male NPT x 3/8” female NPT x 3/8” female NPT; Street T Cotter Pin 1” X 3.
Hitch Assembly # Description Part. No.
Sideboards for 1130, 1250, & 1500 Leaner Models 1130 Sideboards 1250 Sideboards 1500 Sideboards 24
Sideboards for 1130, 1250, & 1500 Leaner Models # Description Part.
Miscellaneous 26 # Description Part. No.
Light Kit Assembly Ground (White Wire) Tail Light (Brown Wire) Field Light (Black Wire) 18 Amber Flashing & Turn Signal (Yellow Wire) 19 Amber Flashing & Turn Signal (Green Wire) # Description Part. No.
WEIGH SCALE SYSTEMS Digi-Star 5-Point Scale System For Single Wheel Applications with Bolt-on Axles 13 12 GT-400 # Description Part. No.
WEIGH SCALE SYSTEMS Digi-Star 5-Point Scale System Hardware Hardware for Single Wheel and Track System Bolt-on Axles GT-400 GT-460 # Description Part. No.
WALKING TANDEM DUAL WHEEL ASSEMBLY # Description Part. No. 1 2 3 4 4 5 6 1”-14 Gr8 YZ Hex Nut (1HNG8) 1-1/4” x 8” x 14” Clamp Plate (114814CP) 1”-14 x 7-1/2” Gr8 YZ Hex Bolt (1712G8HB) Frame Weldment (Left)(FW-1L) Frame Weldment (Right)(FW-1R) 1-3/4” x 13-1/2” Bolt (1341312HB) 1-3/4”-12 Z Gr5 Hex Jam Nut (134JN) JM0019926 JM0010145 JM0019925 JM0019922* JM0010082* JM0019981 JM0009752 7 8 8 9 10 11 12 13 3-3/4” Dia.
STORM TRACKER TRACK SYSTEM # Description Part. No. # Description Part. No. 1 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 Track Carriage Beam Frame Weldment 6” ID Bronze Bushing 1”-8 x 4-1/2” Gr5 Z Hex Bolt 1”-8 x 5-1/2” Gr5 Z Hex Bolt G848 Hub Cpt.
STORM TRACKER TRACK SYSTEM # Description Part. No. # Description Part. No.
Auto-Log Kit # Description Part. No. 1 Auto-Logger 25’ Wire Bundle JM0015445 2 Rotation Counter Sensor Wire bundle JM0015447 3 Rotation Counter Mounting Bracket JM0015448 4 Steel Sensor Target Screw Clamp JM0015450 5 Rotation Counter Sensor Extension Wire Bundle JM0015452 Door Wheel Assembly # Description Part. No.
Roll Tarp Assembly A B C 34 D
Roll Tarp Assembly # Description Part. No. # Description Part. No.
Service / Maintenance Record Date Description Notes For any service instructions, visit our website at www.jm-inc.
