O P E R A T O R ’ S PAT E N T E D GRAIN M A N U A L SINGLE AUGER CARTS 1325-22D Grain Cart J. & M. Mfg. Co., Inc. P.O. Box 547 Ft. Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 JMMAN0101 (Rev. 09/13/06) www.jm-inc.
TO THE DEALER: Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration Card attached to the front inside cover of this manual and return to J. & M. Mfg. Co., Inc. at the address indicated on the card. Warranty claims will be denied if the Warranty Registration Card has not been completed and returned.
MODEL 1325-22D GRAIN CART SPECIFICATIONS DIMENSIONS A) 1’-6” B) 21’-9” C) 8’-6” D) 25’-6” E) 34’-5” F) 14’-8” G) 6’-4” H) 12’-2” I) 1’-5” J) 5’-0” K) 10’-0” L) 11’-9” M) 11’-4” SPECIFICATIONS Capacity Auger, one vertical Wheels Hubs Spindles Weight (approx.) PTO Tire Size Tongue Weight: Empty Loaded Construction: Hopper Undercarriage Wheel Pivot Pin Unloading Time** 1,310+ bushels 22” diameter 18x42 HD 10 bolt 4-1/2” diameter 19,100 Lbs.
GENERAL INFORMATION BOLT TORQUE CHART Always tighten hardware to these values unless a different torque or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
TABLE OF CONTENTS INTRODUCTION 2 EXPRESS WARRANTY 2 SPECIFICATIONS 3 GENERAL INFORMATION 3 BOLT TORQUE CHART 4 SAFETY RULES 6 SAFETY SIGNS 7 INITIAL OPERATION 8 OPERATION 9-11 ROUTINE MAINTENANCE 11 TROUBLE SHOOTING 12 SERVICE 13-14 STORAGE 14 REMOVING FROM STORAGE 14 PARTS LISTS/DIAGRAMS 15-21 WEIGH SCALE INSTALLATION INSTRUCTIONS 22-23 ROLL TARP INSTALLATION 24-28 SERVICE RECORDS 29 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be erased by an operator’s single careless act. In addition, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
50-16 OWNER’S MANUAL SAFETY SIGNS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged or Missing! IMPORTANT: Install new safety signs if the old signs are destroyed, lost, painted over or cannot be read. When parts are replaced that have safety signs, make sure you install a new sign with each new part. New signs are available from the manufacturer or your authorized dealer. 3 1 7 2 Not Shown 4 17 5 16 14 7 Ref.
INITIAL OPERATION/MAINTENANCE BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART.
OPERATING INSTRUCTIONS BE CERTAIN THAT ALL POWER IS SHUT OFF WHEN HOOKING UP TO TRACTOR OR CONNECTING HYDRAULIC LINES TO TRACTOR. Preparing the Grain Cart for Use (see tractor recommendation for grain cart model below): Model 1325-20 and 1325-22 Grain Carts require a 4WD tractor. IMPORTANT: Do NOT pull loaded grain cart on highway. For incidental highway travel, observe the section below. Tow Loads Safely Stopping distance increases with speed and weight of towed loads, and on slopes.
IMPORTANT: 1) Hookup grain cart to tractor using a good quality hitch pin. Attach a safety chain (not included as standard equipment) to the tractor and around the A-frame of the cart as shown. Make sure the grain cart hitch properly matches the hitch of the tractor. Use a single prong (spade) grain cart hitch with a tractor double prong (clevis) hitch. Use a double prong (clevis) grain cart hitch with a single prong (spade) tractor hitch.
LUBRICATION SERVICE SCHEDULE IMPORTANT: Your Grain Cart has grease fittings at all critical points. These should be serviced before the cart is put into operation. BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART. Hitch: There is a grease fitting located on the pivot shaft of the swivel hitch. PTO & Drive Line: The grease fittings on the PTO should be serviced after every 8 hours of use.
TROUBLE SHOOTING MAKE SURE THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY QUALIFIED SERVICEMEN ONLY. Trouble... Possible Cause ... Possible Remedy ...
ADJUSTING THE SLIP CLUTCH After the first hour of operation, the slip-disc clutch should be checked for overheating. After this first check, the slip-disc clutch should be checked weekly or anytime there is excessive slippage of the friction discs. The slip-disc clutch should be checked for moisture, which could cause corrosion on the drive plates.
REMOVING DIRT FROM RESTRICTERS ON HYDRAULIC CYLINDER MAKE SURE THAT ALL POWER IS SHUT OFF AND THE UPPER AUGER TUBE IS IN THE DOWN POSITION BEFORE REMOVING THE RESTRICTERS. Remove restricters from 90 degree street elbow on hydraulic cylinder. Remove dirt from fitting to allow hydraulic oil to flow freely through the restricter. Reattach the restricter to the street elbow. Use teflon sealant tape or equivalent on the threads of the restricter before reattaching.
REPAIR PARTS LIST AND DIAGRAMS When performing maintenance work, wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing and head. Follow Operator’s Manual instructions to ensure safe and proper maintenance and repair. Your local, authorized dealer can supply genuine replacement parts. Substitute parts may not meet original equipment specifications and may be dangerous. BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE PERFORMING ANY MAINTENANCE OR REPAIR WORK.
POWER TAKE-OFF SHAFT # Part # Description 1 28428 Complete Collar Yoke C15 2 18130 Cross Journal Set 3 18133 Outer Yoke 4 00243 Roll Pin for Outer Tube 5 18210 Bush with Grease Nipple 6 30710 Complete Outer Tube 7 90010 Inner Tube 8 00271 Roll Pin for Inner Tube 9 18134 Inner Yoke 10 84033 Complete Slip Clutch 11 19121 Retain Collar for Outer Tube 12 19122 Retain Collar for Inner Tube 13 27820 Complete Guard 14 00452 Outer Circlip 15 16490 Sliding Sleeve Collar
DRIVE LINE ASSEMBLY # 1 2 3 4 5 6 7 Part # 252288 UCF-20928 38112 SS-3812 SS-1212 DS-134192 GDS-134192 8 3S-DUJ 9 CK-44R Description U-Joint (drive shaft to gearbox) 1 3/4" Flange Bearing, 4 hole 3/8" x 1 1/2" Half Moon Key 3/8" x 1/2" Set Screw 1/2"-20 x 1/2" Set Screw Drive Shaft, 1 3/4" x 192" Guard for Drive Shaft (incl.
HYDRAULIC CYLINDER ASSEMBLY (To Raise and Lower the Upper Auger) # 1 2 Part # JD324 JD324-1 3 4 5 6 7 ICR4 38SE90 5602-6-6 PC-37 BJW-114 8 9 10 11 12 13 HN-114 1404-062 HH-1421 HH-14218 HH-14206 RG-1 Description 3" x 24" Hyd. Cylinder Seal Kit for 3" x 24" Hydraulic Cylinder 1" x 4" Pin with Hair Pin 3/8" Street Elbow 90 3/8" Street Tee Pilot Check Valve Ball Joint Weldment with 1 1/4" Hex Nuts 1 1/4" Hex Jam Nut Orifice Restrictor (.
HYDRAULIC DRIVEN FLOW CONTROL SPOUT # 1 2 3 4 Part # FSH-22NS HP-22 BP-22R HC-FCS 5 6 7 8 9 SKHC-FCS HH-14382 PQC-1 SR-14 CP-12112 10 11 12 13 14 15 16 1434-HHMB LN-14 122-HHMB HN-12 STS-1L RCH-1 14STEL Description Flow Control Spout Housing Hinge Baffle Plate Hydraulic Cylinder w/clevis end and 1/2"-20 regular nut Seal Kit for Hydraulic Cylinder 1/4" x 382" Hydraulic Hose Pioneer Quick Coupler 1/4" Swivel Restricter 1/2" x 1 1/2" Clevis Pin w/cotter pin 1/4" x 3/4" Bolt 1/4" Lock Nut 1/2" x 2" Grade
GRAIN CART LIGHT KIT For WESBAR Lighting System with #108060 Light Enhancer For JW Speaker Lighting System with Speaker Light Enhancer # Part # 1 8WH-7PC-S 2 LE-1B-S 3 WH-1-S 4 EL-A1 5 5 6 7 8 9 10 11 12 13 14 15 16 16 RL-R1L-S RL-R1R-S MS-1 FLW-1 FLDLT-1 RD-1A RD-1R RD-1O SMV-1 GR-1 7-WCE AL-1 RL-1A RL-1LH-S 16 RL-1RH-S 17 NC-1MS Description Main Wiring Harness with 7Prong Connector End Light Enhancer (Speaker) Wiring Harness (Rear Half) Extendable Amber Light Assembly (Left/Right) Rear Red Light, Left
ELECTRONIC WEIGH SCALE SYSTEMS FOR GRAIN STORM 1050-22D Scale System Parts List (Digi-Star System) # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part # 278WB-2 375WTS EZ-2000 JB-2 PC-1 ECI-1 37605SA ATP-375 MBI-1 WBW-278 BB-2 343-BWN MB-58612 MB-381 PB-10 Description 2-7/8" Hitch Weigh Bar with cable Weigh Spindle with cable Indicator Box with mounting plate Junction Box (5 pt.
WEIGH SCALE RETROFIT KIT (Continued) MOUNTING THE BATTERY BOX On the rear side of the front, left leg of the grain cart (the leg below the auger hinge), position the Battery Box below and to the right of the grommet as shown. Battery Using the Battery Box as a template, mark and drill two 3/8” holes. Secure the Battery Box to the grain cart leg using two 3/8” x 1” flange bolts and nuts provided. Attach the end plate to the battery box using two 3/8” x 1” flange bolts and nuts.
