Instruction Manual

15
REPAIR PARTS LIST AND DIAGRAMS
When performing maintenance work, wear sturdy, rough-soled work shoes and protective equip-
ment for eyes, hair, hands, hearing and head. Follow Operator’s Manual instructions to ensure
safe and proper maintenance and repair.
Your local, authorized dealer can supply genuine replacement parts. Substitute parts may not
meet original equipment specications and may be dangerous.
BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE PERFORMING ANY MAINTENANCE
OR REPAIR WORK.
# Part # Description
1 FW-1L Frame Weldment (Left)
FW-1R Frame Weldment (Right)
2 334PP 3 3/4” Dia. Pivot Pin
3 PBW-1L Pivot Beam Weldment (left)
3 PBW-1R Pivot Beam Weldment (right)
4 13G8HB 1”-14 x 3” Gr 8 Bolt
5 34-LN 3/4” Lock Nut
6 34512G5HB 3/4” x 5 1/2” Gr 5 Bolt
7 BB-334 3 3/4”ID x 4 1/2” OD
Bronze Bushing
8 134JN 1 3/4” Jam Nut
9 1341312HB 1 3/4” x 13 1/2” Bolt
10 1712G8HB 1”-14 x 7 1/2” Gr 8 Bolt
11 1HNG8 1”-14 Gr 8 Hex Nut
12 114814CP 1 1/4” x 8” x 14” Clamp Plate
13 PCW-1 Pivot Center Weldment
WALKING TANDEM DUAL WHEEL AXLE ASSEMBLY
HUB AND SPINDLE ASSEMBLY
BOLT ON HITCH ASSEMBLY
# Part # Description
1 SHW-112N-25 Swivel Hitch Weldment clevis type (2 1/2” shaft)
1 SHW-278 Swivel Hitch Weldment clevis type (2 7/8” shaft) scales
2 SHW-112SN-25 Swivel Hitch Weldment spade type (2 1/2” Shaft)
2 SHW-278S Swivel Hitch Weldment spade type (2 7/8” Shaft) scales
2 SHW-112SB Swivel Ball Hitch Weldment spade type (2 1/2” shaft)
2 SHW-278SB Swivel Ball Hitch Weldment spade type (2 7/8” shaft)
3 212PC 2 1/2” x 13 1/4” Shaft w/collar
4 1412BN 1” x 4 1/2” Gr 5 HHMB w/nut
5 HSPS-1 Hitch Spool Plate Support
6 WBW-278 Weigh Bar Weldment
7 343BWN 3/4” x 3” Bolt (Gr 8) with Heavy Lock
Washer and Nut
8 343HB 3/4” x 3” Hex Bolt (Gr 8)
9 1512BN 1” x 5 1/2” Bolt (Gr 5) with nut
10 16BN 1” x 6” Bolt (Gr 5) with nut (scales)
Cart equipped WITH Electronic
Weigh System
Cart equipped WITHOUT
Electronic Weigh System
# Part # Description
1 18x38-10 Wheel Rim, 10 hole 18x38
(11.13 pilot) (13.19 bolt circle)
1 16x42-10 Wheel Rim, 10 hole 16x42
(11.13 pilot) (13.19 bolt circle)
2 W-881 Hub with studs and nuts“
(11.13 pilot) (13.19 bolt circle)
3 4T-HM218248 Large Bearing (910346)“(HM218248)
4 HM212049 Small Bearing (910347)“(HM212049)
5 910344 Large Race (HM218210)
6 910384 Small Race (HM212011)
7 CR-43771 Seal (6”OD) 1-906979
7 37605SA Seal (6”OD-3 3/4”ID) for hub with
scales (started 3-1-00)
8 913635 Spindle Washer
9 912973 Slotted Spindle Nut
10 905945 Cotter Pin
11 909921 Dust Cap
12 913564 Wheel Stud, 3/4”-16
13 913571 Wheel Nut, 3/4”-16
14 281900S Spindle (4 1/2” dia. x 20 1/4”)
15 HSA-650S Hub & Spindle Assembly
16 17HBLN 1” x 7” Hex Bolt with Lock Nut