Use and Care Manual

ManualsBrandsJ&E Home ManualsFurnitureGrey/White PC Seat Gaming Chair with 4D Adjustable Arms

GAMING CHAIRS MODELS

TS83, TS84, TS90, TS92,

TSF44, TSC81, XXL2

ATTENTION:

⚠ Follow the instructions step by step.

⚠ To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.

⚠ Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.

⚠ Using the wrong size of screws on a part could result in damage to the screw or the part.

ASSEMBLY INSTRUCTIONS

B C-L

C-R

I-L

I-R

J-N

J-L

Backrest

Seat

Left Armrest

Right Armrest

Mechanism

Gas Lift

Covers for gas

lift, set of 3 pcs

5-leg star base

Casters, 5 pcs.

Left cover for

seat bracket

Right cover for

seat bracket

Neck pillow

Lumbar pillow

Allen wrench

STEP

Insert the casters Ⓗ into the legs of the

base

Ⓖ using

pressure, then place the gas lift Ⓔ in the middle of the

base and cover it with Ⓕ.

Ⓜ

STEP

Note: When sitting on chair, not looking at it

M8x20mm,

4 pcs

M8x25mm,

12 pcs

M5x12mm,

pcs

O-Rings,

16 pcs

Washers,

16 pcs

Hole Covers,

4 pcs

Ⓖ

Ⓔ

Ⓗ

Ⓕ

Ⓛ

Ⓞ

Ⓟ

O-Ring in

the middle!

Ⓓ

(Front)

C-L

C-R

Note: The a

rmrest side is determined by you sitting on the chair, not looking at it

(Back)

C-L

LEFT

C-R

RIGHT

Ⓑ

Assemble the armrests and in the

ir respective

sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ and

washers Ⓟ.

Ⓐ

Put the seat

over the base

parts making sur

the tip of

the gas lift enters

into the hole of the

mechanism, then

assemble the backrest Ⓐ to the metal br

ackets

both sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ

and washers Ⓟ.

Ⓑ

Ⓞ

Ⓟ

O-Ring in

the midd

le!

Ⓜ

Attach the cover

s and to

the brackets on the

respective sides of the seat Ⓑ using screws Ⓝ and

cover the holes with Ⓠ As shown.

I-L

I-R

STEP

I-R

I-L

LEFT

RIGHT

Ⓑ

Ⓝ

First attach the

lumbar pillow then the neck pillow

by fastening the

buckles behind the backrest

Ⓐ as

shown.

J-L

J-N

STEP

Ⓐ

(This shows

The chair

from behind)

J-N

J-L

(Mechanism)

(Backrest, armrest)

4 sets

Ⓞ

Ⓟ

O-Ring in

the midd

le!

8 sets

(Brackets Covers)

Ⓠ

4 pcs

felt gaskets,

4 pcs

C-R

RIGHT

Ⓑ

Ⓓ

B C-L

Turn over the seat Ⓑ with its back end towards you, as shown

below. Place Ⓠ on the four seat mechanism holes. Use

screws Ⓛ, O-rings Ⓞ and washers Ⓟ to install the

mechanism Ⓓ with its knob facing towards the front.

Except TS84

(Back)

Summary of content (2 pages)

PAGE 1
ATTENTION: GAMING CHAIRS MODELS ASSEMBLY INSTRUCTIONS A Backrest B Seat J-N Neck pillow J-L Lumbar pillow TS83, TS84, TS90, TS92, TSF44, TSC81, XXL2 C-L Left Armrest C-R Right Armrest D Mechanism ⚠ Follow the instructions step by step. ⚠ To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places. ⚠ Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.
PAGE 2
CHAIR’S FUNCTIONS: ① To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair goes down while sitting on it, or up if you lift your body. ② To make the chair tilt, pull the same lever OUT horizontally to unlock this function, and IN to lock again. Please note that unlike regular office chairs, gaming chairs have their base components off-center, and the tilting won’t be much and might actually feel hard to tilt.