Use and Care Manual

ManualsBrandsJ&E Home ManualsFurnitureGrey/Black PU Seat Gaming Chair with 3D Adjustable Arms

GAMING CHAIR RTA MODELS

TS42, TS43,

TS50, TS51, TS52,

TS60, TS61, TS62C, TS63C.

ATTENTION:

⚠ Follow the instructions step by step.

⚠ To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.

⚠ Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.

⚠ Using the wrong size of screws on a part could result in damage to the screw or the part.

ASSEMBLY INSTRUCTIONS

B C-L

C-R

I-L

I-R

J-N

J-L

Backrest

Seat

Left Armrest

Right Armrest

Mechanism

Gas Lift

Covers for gas

lift, set of 3 pcs

5-leg star base

Casters, 5 pcs.

Left cover for

seat bracket

Right cover for

seat bracket

Neck pillow *

Lumbar pillow *

Allen wrench

STEP

Insert the casters Ⓗ into the legs of the base

Ⓖ using pressure, then place the gas lift Ⓔ in

the middle of the base and cover it with Ⓕ.

STEP

* When sitting on chair, not looking at it

M8x20mm with

felt gasket,

4 pairs.

Ⓖ

Ⓔ

Ⓗ

Ⓕ

C-L

C-R

Ⓐ

Put the seat over the base parts making sure the tip of

the gas lift enters into the hole of the mechanism, then

assemble the backrest Ⓐ to the metal brackets on

both sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ

and washers Ⓟ.

Ⓑ

Ⓞ

Ⓟ

O-Ring in

the middle!

Ⓜ

Attach the covers and to the brackets on their

respective sides of the seat Ⓑ using screws Ⓝ and

cover the holes with Ⓠ As shown.

I-L I-R

STEP

I-R

I-L

LEFT

RIGHT

Ⓑ

ⓃⓆ

For pillows with straps, first attach the lumbar pillow

then the neck pillow by fastening the buckles

behind the backrest Ⓐ as shown.

J-L

J-N

STEP

Ⓐ

(This shows

The chair

from behind)

J-N

J-L

(Mechanism)

M8x25mm,

12 pcs

M6x12mm,

2 pcs

O-Ring,

16 pcs

Washers,

16 pcs

(Armrest, Backrest)

(Brackets Covers)

Hole covers,

2 pcs

STEP

Note: The armrest side is determined by you sitting on the chair, not looking at it

(Back)

(*) Except TS61 and TSC62C

* The shape of these 2 pieces varies on each model.

* TS61 & TS62C don’t not come with lumbar pillow.

Ⓛ

Ⓞ

Ⓟ

O-Ring in

the middle!

Ⓓ

Ⓑ

(Back)

IMPORTANT:

Felt gasket goes

over the seat’s

hole!

Flip over the seat Ⓑ with its back end towards you, peel and place

the felt gasket Ⓛ over the holes on the seat, and using screws Ⓛ,

O-rings Ⓞ and washers Ⓟ, assemble the mechanism Ⓓ with its

handle facing to the LEFT as shown.

4 sets:

C-L

LEFT

C-R

RIGHT

Ⓑ

Ⓞ

Ⓟ

O-Ring in

the middle!

8 sets:

Ⓜ

Assemble the armrests and in their respective

sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ and

washers Ⓟ.

Summary of content (2 pages)

PAGE 1
ATTENTION: GAMING CHAIR RTA MODELS ASSEMBLY INSTRUCTIONS A Backrest C-R Right Armrest D Mechanism C-L Left Armrest B Seat ⚠ Follow the instructions step by step. ⚠ To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places. ⚠ Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes. ⚠ Using the wrong size of screws on a part could result in damage to the screw or the part.
PAGE 2
CHAIR’S FUNCTIONS: ① To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair goes down while sitting on it, or up if you lift your body. ② To make the chair tilt, pull the same lever OUT horizontally to unlock this function, and IN to lock again. Please note that unlike regular office chairs, gaming chairs have their base components off-center, and the tilting won’t be much and might actually feel hard to tilt.