3.2 Description of Icon 3.2.1 LCD ICON 1) VOX (Voice Activated Transmission) Indicator - Appears when VOX is activated. 2) Auto Scan Indicator - Icon appears when the Normal scan channel mode and Priority scan channel mode is activated. 3) Alarm Indicator - Appears when the alarm mode is on . 4) Weather Alert Indicator - Appears when the Weather alert is selected . 5) Received Signal Strength Indicator - Appears when carrier is detected in the two way mode .
PWR AUTO PWR LOW < SETUP MANU > - In the use of default When the power on state. (1~7CH,GMRS:2W /8~14CH,FRS:0.5W /15~22CH,GMRS:2W) - In the use of Only 0.5W for manual. (1~22CH,GMRS/FRS:0.5W ) 3.2.2 Description of Button function 1. Power Button(1) - To turn the Unit ON, press and hold the Power Button(1). - To turn the Unit OFF, press and hold the Power Button(1) for more than 1, 2 second. 2.
3) SCAN selection Pressing the menu button(2, 3) in the Channel/Code Selection menu allows you to enter the Scan Selection menu with key beeping. Pressing the up/down button(5, 6) in the Scan Selection mode allows you to select Off, Normal scan or Priority scan while icon is blinking. If you select the Normal scan, it starts to scan the channel from the current channel. If you select the priority scan, it scans the current channel and priority channel in turn. You can select Priority channel in setup mode.
2) FM Fine Tune Pressing the menu button (3) in the FM see k menu allows you to enter FM tuning menu. You can increase and decrease FM broadcast frequency by 100 Hz using the up/down button(5, 6). 3) FM Preset Memory Pressing the menu button (3) in the FM Fine menu, “MEM OFF” is displayed on LCD monitor. And the n Pressing the up/down button(5, 6) allows you to select “MEM ON”, then press the Menu button(3). If that is so, “M1 87.5” is displayed and “1” blinks. It means that broadcast channel of 87.
Pressing the menu key (left/right arrow key) in the Weather Channel Selection menu allows you to enter Weather Alert Selection menu. You can select ALERT ON/OFF by using the up/down arrow key. (DEFAULT=OFF) If the WEA Alert On, this radio always detects the weather Alert On, this radio always detects the weather alert signal(=1050Hz) of weather channel. 3.
Pressing the menu button (3) in the Unit Selection menu enters the Alarm Set menu and you can select Alarm function(OFF, ON, +TX) by using the up/down button(5, 6). OFF : Alarm OFF ON : Alarm ON +TX : If Alarm is on, The unit transmit unit name and temperature automatically (emergency selective calling) 3) Alarm Limit Temperature set Two conditions of Alarm operation Alarm AL H: AL L: alarm AL L: AL H: Alarm Pressing the menu button(3), then “AL H: 0C” is displayed on LCD monitor.
Pressing the menu button(3) in the Time calibration menu allows you to enter the alarm selection menu and you can select the Alarm OFF/Alarm ON by using up/down button(5, 6). If the alarm is on, Alarm icon ( ) is displayed and the radio makes a alarm beeping at the set time. 3) Alarm time set Pressing the menu button(3) in the Alarm selection menu allows you to enter the Alarm time set menu, you can select hour/minute or AM/PM by using menu button(2, 3) and change setting time by using up/down button(5, 6).
3) “CALL ” : CALL beep sound selection You can select call beep sound out of off/1/2/3/4/5/6/7 by using up/down button(5, 6). 4) “RING ” : CALL signal selection “ R ” : Only received call sound. 5) “ROGER ” : ending sound selection when transmission is ended This menu decide that the unit transmit ending sound or not when transmission is terminated. 6) “BEEP ” : key beep selection This menu decide that beep sound is produced or not when key button is pressed.
