SDS

Source
Ingredient
Material name
TWA
STEL
Peak
Notes
Ingredient
TEEL-1
TEEL-2
TEEL-3
Ingredient
Original IDLH
Revised IDLH
Ingredient
Occupational Exposure Band Rating
Occupational Exposure Band Limit
Notes:
Occupational exposure banding is a process of assigning chemicals into specific categories or bands based on a chemical's potency and the
adverse health outcomes associated with exposure. The output of this process is an occupational exposure band (OEB), which corresponds to a
range of exposure concentrations that are expected to protect worker health.
US OSHA Permissible Exposure
Limits (PELs) Table Z-1
iron
Particulates Not Otherwise Regulated
(PNOR)- Respirable fraction
5 mg/m3
Not
Available
Not
Available
Not Available
US OSHA Permissible Exposure
Limits (PELs) Table Z-1
iron
Particulates Not Otherwise Regulated
(PNOR)- Total dust
15 mg/m3
Not
Available
Not
Available
Not Available
US OSHA Permissible Exposure
Limits (PELs) Table Z-3
iron
Inert or Nuisance Dust: Total Dust
15 mg/m3 / 50
mppcf
Not
Available
Not
Available
Not Available
US OSHA Permissible Exposure
Limits (PELs) Table Z-3
iron
Inert or Nuisance Dust: Respirable fraction
5 mg/m3 / 15
mppcf
Not
Available
Not
Available
Not Available
US NIOSH Recommended
Exposure Limits (RELs)
iron
Particulates not otherwise regulated
Not Available
Not
Available
Not
Available
See
Appendix D
Emergency Limits
bisphenol A diglycidyl ether
polymer
90 mg/m3
990 mg/m3
5,900 mg/m3
1,4-butanediol diglycidyl ether
16 mg/m3
170 mg/m3
220 mg/m3
iron
3.2 mg/m3
35 mg/m3
150 mg/m3
bisphenol A diglycidyl ether
polymer
Not Available
Not Available
bisphenol F diglycidyl ether
copolymer
Not Available
Not Available
1,4-butanediol diglycidyl ether
Not Available
Not Available
iron
Not Available
Not Available
Occupational Exposure Banding
bisphenol F diglycidyl ether
copolymer
E
≤ 0.1 ppm
1,4-butanediol diglycidyl ether
E
≤ 0.1 ppm
Exposure controls
Appropriate engineering
controls
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls can
be highly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection.
Personal protection
Eye and face protection
Safety glasses with side shields.
Chemical goggles.
Skin protection
See Hand protection below
Hands/feet protection
Wear chemical protective gloves, e.g. PVC.
Wear safety footwear or safety gumboots, e.g. Rubber
NOTE:
The material may produce skin sensitisation in predisposed individuals. Care must be taken, when removing gloves and other protective
equipment, to avoid all possible skin contact.
The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary from manufacturer to
manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove material can not be calculated in advance
and has therefore to be checked prior to the application.
Body protection
See Other protection below
Other protection
Overalls.
P.V.C apron.
SECTION 9 Physical and chemical properties
Information on basic physical and chemical properties
Appearance
Black Liquid
Physical state
Liquid
Relative density (Water = 1)
Not Available
Odor
Not Available
Partition coefficient n-octanol
/ water
Not Available
Version No:
6.7
Page
4
of
9
J-B Weld Original Part A
Issue Date:
10/24/2022
Print Date:
10/24/2022
Continued...