Datasheet

ManualsBrandsIxxat ManualsAutomationCAN@net NT 420 CAN bus Ethernet, CAN, USB 24 V DC 1 pc(s)

Table Of Contents

V1.0

www.ixxat.com

Page 1 of 3

The Ixxat CAN@net NT 420 with four CAN channels (thereof two

channels switchable to CAN FD) is a three-in-one multifunctional

talent in the CAN world and a very reliable workhorse for CAN

applications. It can act as a gateway between CAN/CAN FD and

Ethernet systems, providing easy, flexible access to up to four

independent CAN or two CAN FD systems via LAN or over the

Internet.

As a CAN-Ethernet-CAN bridge the CAN@net NT 420 allows the

exchange of CAN messages between CAN/CAN FD systems over

long distances via TCP/IP, using existing Ethernet infrastructures.

The segmentation of CAN/CAN FD systems also increases the

reliability and failure safety of the entire system.

Messages can be processed, filtered and mapped in the

gateway.Inaddition,dependingonthereceivedmessagesand

the status of the device or CAN bus, various actions and

responses can be automatically performed. The MQTT protocol

available in CAN@net NT 420 enables the information to be

transmitteddirectlytothecloud.

Galvanic isolation reliably enhances the protection of the device

against damage to electronics caused by voltage peaks.

FEATURES AND BENEFITS

Easy coupling of CAN and CAN-FD systems and devices

■

Allows system expansion and tree/star topologies

■

Cost savings due to simple wiring

■

Increased system reliability

■

4 x CAN channels, thereof 2 x channels switchable to CAN FD

■

Line protection by galvanic isolation

■

Bridging of large distances with CAN-to-Ethernet-to-CAN

■

Easy remote system access

■

Powerful filter, ID translation, data mapping and multiplexing

functionality

■

Additional programming of any kind of action rules using LUA

■

MQTT support for easy cloud connection

■

Powerful programming interface for Windows (VCI) as well as for Linux

(socketCAN or ECI), QNX, RTX, INtime and VxWorks (ECI)

■

DATASHEET

CAN@net NT 420

Summary of content (3 pages)

PAGE 1
DATASHEET CAN@net NT 420 The Ixxat CAN@net NT 420 with four CAN channels (thereof two channels switchable to CAN FD) is a three-in-one multifunctional talent in the CAN world and a very reliable workhorse for CAN applications. It can act as a gateway between CAN/CAN FD and Ethernet systems, providing easy, flexible access to up to four independent CAN or two CAN FD systems via LAN or over the Internet.
PAGE 2
ORDER NUMBER 1.01.0332.42000 CAN channels (high speed) 4 CAN FD / CAN channels 2 CAN bus interface 4 x CAN high speed according to ISO 11898-2:2016, 2 x switchable to CAN FD according to ISO 11898-1:2015 CAN bit rates CAN FD bit rates 5 kbit/s to 1000 kbit/s Arbitration rate: up to 1000 kbit/s, data rate: up to 8000 kbit/s (verified by testing). User defined bit rates are possible. CAN bus termination resistors None Galvanic isolation CAN propagation delay (typical) 1 kV DC for 1 sec.
PAGE 3
ACCESSORIES ORDER NUMBER CAN Y cable 2.1 m 1.04.0076.00002 PIN ALLOCATION TECHNICAL DRAWING CAN CONNECTORS 1 2 3 4 2 3 4 2 3 4 CAN-High CAN-Low CAN-GND Shield POWER CONNECTOR 1 1 3 4 6 7 5 CONNECTORS 1 = CAN 1 2 = CAN 2 3 = CAN 3 4 = CAN 4 5 = Ethernet (RJ45) 6 = Mini-USB 7 = POWER V+ (+9 V to +36 V DC) V- 1 2 7 SOFTWARE SUPPORT Configuration The configuration of the CAN@net NT and the firmware upload is done with an intuitive to operate Windows configuration tool via USB or Ethernet.