Datasheet

ManualsBrandsIxxat ManualsAutomationGateway Ethernet, RJ-45 Ixxat

Table Of Contents

V1.0

www.ixxat.com

Page 1 of 3

The Ixxat CAN@net NT 200 with two CAN channels is a three-in-

one multifunctional talent in the CAN world and a very reliable

workhorse for CAN applications. It can act as a gateway between

CAN and Ethernet systems, providing easy, flexible access to two

independent CAN systems via LAN or over the Internet.

As a CAN-Ethernet-CAN bridge the CAN@net NT 200 allows the

exchange of CAN messages between CAN systems over long

distances via TCP/IP, using existing Ethernet infrastructures. The

segmentation of CAN systems also increases the reliability and

failure safety of the entire system.

Messages can be processed, filtered and mapped in the

gateway, in addition a wide variety of actions can be performed

automatically in response to received messages and device or

CAN bus statuses. The MQTT protocol available in CAN@net NT

200 enables the information to be transmitted to the cloud.

Galvanic isolation reliably enhances the protection of the device

against damage to electronics caused by voltage peaks.

FEATURES AND BENEFITS

ORDER NUMBER 1.01.0332.20000

CAN channels (high speed) 2

CAN bus interface 2 x CAN high speed according to ISO 11898-2:2016

Easy coupling of CAN systems and devices

■

Allows system expansion and tree/star topologies

■

Cost savings due to simple wiring

■

Increased system reliability

■

2 x CAN channels

■

Line protection by galvanic isolation

■

Bridging of large distances with CAN-to-Ethernet-to-CAN

■

Easy remote system access

■

Powerful filter, ID translation, data mapping and multiplexing

functionality

■

Additional programming of any kind of action rules using LUA

■

MQTT support for easy cloud connection

■

Powerful programming interface for Windows (VCI) as well as for Linux

(socketCAN or ECI), QNX, RTX, INtime and VxWorks (ECI)

■

DATASHEET

CAN@net NT200

Summary of content (3 pages)

PAGE 1
DATASHEET CAN@net NT200 The Ixxat CAN@net NT 200 with two CAN channels is a three-inone multifunctional talent in the CAN world and a very reliable workhorse for CAN applications. It can act as a gateway between CAN and Ethernet systems, providing easy, flexible access to two independent CAN systems via LAN or over the Internet. As a CAN-Ethernet-CAN bridge the CAN@net NT 200 allows the exchange of CAN messages between CAN systems over long distances via TCP/IP, using existing Ethernet infrastructures.
PAGE 2
ORDER NUMBER 1.01.0332.20000 CAN bit rates 5 kbit/s to 1000 kbit/s CAN FD bit rates - CAN bus termination resistors None Galvanic isolation CAN propagation delay (typical) 1 kV DC for 1 sec. Local CAN Bridge: 25-50 µs depending on configuration settings and CAN load. CAN-Ethernet-CAN Bridge: 4-6 ms Messages per second (send/receive) 30000-40000 msg/s in Bridge mode USB connector Mini-USB 2.
PAGE 3
PIN ALLOCATION TECHNICAL DRAWING CAN CONNECTORS 1 2 107 mm 2 3 4 POWER CONNECTOR 1 2 3 4 22,5 mm CAN-High CAN-Low CAN-GND Shield 4 5 99 mm 1 3 V+ (+9 V to +36 V DC) V5 2 SCREW CONNECTORS 1 = CAN 1 2 = CAN 2 3 = Ethernet (RJ45) 4 = Mini-USB 5 = POWER 1 114,5 mm SOFTWARE SUPPORT Configuration The configuration of the CAN@net NT and the firmware upload is done with an intuitive to operate Windows configuration tool via USB or Ethernet.