Installation Instructions

6) Thread one small threaded pipe into end of loop[F].
7) Pass xture wire through loop. Thread loop onto end of last
stem.
8) Take threaded pipe[H] from parts bag and screw in screw
collar loop[K] a minimum of 6 mm (1/4”). Lock into place with
hexnut[J].
9) Run another hexnut down threaded pipe almost touching
rst hexnut. Screw threaded pipe into mounng strap[G].
Mounng strap must be posioned with extruded thread
faced into outlet box[I]. Threaded pipe must protrude out
the back of mounng strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounng strap.
10) Connect mounng strap to outlet box using strap mounng
screws[O].
11) Unscrew the threaded ring from screw collar loop. Take
canopy[D] and pass over screw collar loop. Approximately
one half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounng strap. Remove canopy.
12) Aer desired posion is found, ghten both top and boom
hexnuts up against the boom and top of the mounng strap.
13) Slip canopy over screw collar loop and thread on threaded
ring[C]. Aach chain link[E] (with xture connected) to
boom of screw collar loop. Unscrew threaded ring[C], let
canopy and threaded ring slip down. (Close chain link ends
together using chain pliers or padded pliers to prevent damage
to nish.)
14) Weave electrical wire and ground wire through chain links.
Pass wire through threaded ring, canopy, screw collar loop,
threaded pipe and into outlet box.
15) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole
and two raised dimples, wrap ground wire from outlet box
around green ground screw, and thread into hole.
b) On xtures where a cupped washer is provided, aach
ground wire from outlet box under cupped washer and
green ground screw, then thread into mounng strap.
If xture is provided with ground wire. Connect xture ground
wire to outlet box ground wire with wire connector (Not
provided) aer following the above steps. Never connect
ground wire to black or white power supply wires.
16) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply Wire
to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or Black
without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other than
green) with silver conductor
*Note: When parallel wire (SPT 1 &
SPT 2) are used. The neutral wire
is square shaped or ridged and the
other wire will be round in shape or
smooth (See illus.)
Neutral Wire
17) Raise canopy to ceiling.
18) Secure canopy in place by ghtening threaded ring onto screw
collar loop.
19) Insert recommended bulbs[S] (Not supplied).
20) Carefully raise glass[T] to the xture. Slip the opening over
the socket and t the glass against the socket cup and gently
rotate the glass clockewise unl seated in place.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Long Stem
[B] Short Threaded
Tubes
[C] Threaded Ring
[D] Canopy
[E] Chain Link
[F] Loop
[G] Mounting Strap
[H] Threaded Pipe
[I] Outlet Box
[J] Hexnut
[K] Screw Collar
Loop
[L] Short Stem
[M] Coupler
[N] Center Column
[O] Strap Mounting
Screws
[P] Support Rods
[Q] Studded Knobs
[R] Lower
Assembly
[S] Bulb
[T] Glass
[U] Threaded Rod
with Hexnut
I
H
K
J
O
C
►
S
T
R
A
►
B
M
L
Q
P
Q
N
U
G
►
D
E
F
B
1) Take the threaded rod with hexnut[U] and thread into the
lower assembly[R].
2) Slide center column[N] over installed threaded rod.
3) Install the six (6) support rods[P] using the twelve (12)
studded knobs[Q].
4) Thread into place the coupler[M] onto the top of the center
column.
5) Pass xture wire through desired amount of long stem[A] &
short stem[L] and screw stems together using supplied short
threaded tubes[B] and thread into center column[N].
NOTE: Thread locking compound must be applied to all stem
threads as noted with (4) symbol to prevent accidental
rotaon of xture during cleaning, relamping, etc.
Installaon Instrucons (connued)