Instructions / Assembly

ManualsBrandsIvation ManualsGarden CenterAir Conditioner One Leg Window Support Mounting Bracket - 19"

AIR CONDITIONER BOTTOM

WITH WINDOW PANEL FRAME

WINDOW

FRAME

LEDGE

WINDOW SILL

SIDE VIEW

FRAME

Universal

Air Conditioner

Support Bracket

SKU: IVAMINIMOUNT

User Guide

Thank you for purchasing the Ivation®

Universal Air Conditioner Support

Bracket. This User Guide is intended to

provide you with guidelines to ensure

that operation of this product is safe

and does not pose risk to the user. Any

use that does not conform to the

guidelines described in this User Guide

may void the limited warranty.

Please read all directions before using

the product and retain this guide for

reference. This product is intended for

household use only. It is not intended f

or commercial use.

This product is covered by a limited

one-year warranty. Coverage is subject

to limits and exclusions. See warranty

for details.

1. INTRODUCTION

Safety Precautions

WARNING: Use with products heavier

than the rated weight capacity of

170 lbs. (77 kg) may result in bracket

instability, causing possible injury.

• ⚠WARNING: CHOKING HAZARD—

Small parts. This product contains

small parts that could present a

choking hazard if swallowed and is

not suitable for children under three

(3) years old.

• Please follow the assembly instructions

as directed. Improper installation of

this bracket may result in damage or

serious personal injury.

• Make sure to use safety gear and

proper tools while installing this

bracket. This product should only be

installed by professionals.

• Make sure that the supporting surface

will safely bear the combined weight

of the equipment and all the additional

hardware and components prior to

beginning installation.

• Only use the mounting screws provided

and do not overtighten mounting screws.

• Please verify that you have received all

included parts and they are in good

condition prior to beginning installation.

2. SAFETY

Installation Instructions

1. Determine the approximate center of

gravity, or if one side is heavier than

the other. To do this, set the air

conditioner on the ground. Partially lift

each side (left and right, not front and

back) to determine if the weight is

centered, or if the right or left side

is heavier.

2. Measure the length of the window

frame opening where the air

conditioner will sit. Divide the length

of the window frame in half, and make

a mark directly in the center with

your pencil.

3. Place the center of concave block (A)

over the mark, on the window frame,

against the window ledge. Set the

rounded spacer (B) on top of the

concave block (A). Move the two

blocks together in a straight line

directly away from the window ledge

until the top of the rounded spacer

while resting on top the concave block

is even with the ledge. If the blocks are

even with the ledge, you can leave

them positioned against the ledge.

NOTE: If your air conditioner has an

adjustable window panel that goes in the

window opening, make sure to position

the concave block (A) and rounded

spacer (B) so that the window panel has

room to ﬁt between them. If the air

conditioner support touches the window

frame, add ONE ﬂat spacer (C).

4. If the weight of the air conditioner was

evenly balanced, you can leave your

mark directly in the center of the frame.

However, if the weight was heavier on

either side, make a new mark three

inches (3") in the direction of the

heavier side.

5. Using the 5/32" drill bit, drill a hole

where your ﬁnal mark position ended

up, two inches (2") into the window

frame. Then, use the drill to secure the

concave block (A) with the short

screw (D) to the frame.

NOTE: Make sure that your window

frame is not hollow or ﬁlled with foam —

these will not allow the air conditioner

support bracket to properly hold your

air conditioner’s weight. If you need to

drill down further than two inches to

reach solid material, make sure to do so.

6. Make sure that the support body (E)

will clear any obstacles on the

windowsill (such as raised edges of the

window frame, molding, etc.) using the

rounded spacer (B) and the concave

block (A). If not, use ONE ﬂat spacer

slightly higher than the window ledge,

the weight will still hold.

4. INSTALLATION

A. Concave block (1)

B. Rounded spacer (1)

C. Flat spacer extender* (2)

D. Short screw (1)

E. Support body (1)

F. Long screws (2)

G. Support leg (1)

H. Hex bolt-neck screw (1)

I. Level (1)

J. Washer (2)

K. Nut (1)

L. User guide

*Please note that while you are given

multiple ﬂat spacer extenders, we only

recommend using one at a time. The

screw can only pass through the concave

block, rounded spacer, and one

ﬂat extender.

You will also need:

• Wrenches or sockets (7/16") – 2

• Drill with 5/32" bit

• #3 Phillips head screwdriver

• Tape measure

• Pencil

3. CONTENTS

Sill

Interior

Ledge

Sill

Exterior

Summary of content (2 pages)

PAGE 1
2. SAFETY Universal Air Conditioner Support Bracket SKU: IVAMINIMOUNT User Guide 3. CONTENTS 4. INSTALLATION Safety Precautions Installation Instructions WARNING: Use with products heavier than the rated weight capacity of 170 lbs. (77 kg) may result in bracket instability, causing possible injury. 1. Determine the approximate center of gravity, or if one side is heavier than the other. To do this, set the air conditioner on the ground.
PAGE 2
7. WARRANTY c. Gradually slide the leg toward the outer end of the support body frame until the bubble moves offcenter, toward you and the window. The frame should be slightly angled down toward the ground outside the window. 10. Align the spacer (B/C) and concave block (A) assembly with the support body (E) overtop the mounting holes and tighten the long screws (F) that were previously not tightened all the way down. Once tightened, loosen them by half a turn.