Mobile Collection Hardware Installation Guide
Identification Mobile Collection Hardware Installation Guide 01/08/2009 TDC-0770-002 Copyright © 2007 - 2009 Itron, Inc. All rights reserved. Trademark Notice Itron is a registered trademark of Itron, Inc. All other product names and logos in this documentation are used for identification purposes only and may be trademarks or registered trademarks of their respective companies.
Contents Using the MC3 System .................................................................................................. 1 About the MC3 System .......................................................................................................................1 Mobile Collection Hardware Kit .................................................................................................1 Installing the MC3 System ..................................................................................
Contents Insert the Flash Card ....................................................................................................47 Remove the Flash Card ................................................................................................48 Removing the Mobile Collection 2.x System .....................................................................................48 Unlock and Remove the GoBook............................................................................................
CHAPTER 1 Using the MC3 System This chapter introduces you to the features, functions, and components of Mobile Collection 3.0 (MC3) system. About the MC3 System The MC3 is Itron's powerful, next-generation mobile collection system for electric, gas and water providers. It offers advanced radio technology for unsurpassed performance, along with a sophisticated mapping application utilizing GPS technology that provides a visual indication of endpoint location.
Chapter 1 Using the MC3 System ID 1 Item MC3 radio Description Includes a mounting harness and straps for installing the system in your vehicle. 2 USB cable Comes attached to the dock and attaches to the GoBook. Provides communication between GoBook and MC3 radio. 3 GoBook XR-1 Runs the Mobile Collection software to collect reads. The MC3 radio is also compatible with the GoBook III laptop. 4 GoBook dock The GoBook, power cables, and communication cables attach to the dock.
Installing the MC3 System WARNING! Install the Mobile Collection system in the vehicle as described in this document and those listed above. Failure to do so could lead to injury or death from unsecured components during a collision. About the Sled The Mobile Collector sled is used to securely fasten the GoBook in the vehicle. It is placed on the passenger seat and secured with a seat belt and pretensioner.
Chapter 1 Using the MC3 System ID 3 Item GoBook dock Description Attaches to the GoBook and provides a secure base for the laptop while in the vehicle. Docks are available for use with both XR-1 and GoBook III models. About the Seat Belt Pretensioner The seat belt pretensioner makes the modern three-point safety harness in your vehicle function similarly to an old-fashioned lap seat belt.
Installing the MC3 System To install the seat belt pretensioner Follow the procedures in the Mobile Collector Sled and Pretensioner Installation Guide (TDC-0708-xxx). A DVD showing the installation is also included with your kit. These materials are located in a plastic sleeve on the underside of the sled. Installing the Junction Box The junction box takes power from the vehicle and distributes it to the MC3 radio, GoBook, and an optional EkaNet radio (when installed).
Chapter 1 Using the MC3 System 4. Slide one end of the junction box into position over the bracket that is still attached; be sure to orient the junction box according to the label on the sled or pedestal. The junction box has a recessed edge that the bracket fits into. 5. Insert the other bracket (the one you removed) into the junction box, making sure that both screw holes are visible through the bracket. 6. Insert and tighten both screws to secure the junction box to the sled or pedestal.
Installing the MC3 System A dock is also available for use with the GoBook III laptop; see Attaching the GoBook III to the Vehicle Dock on page 23 for more information. Attaching the GoBook XR-1 to the Dock 1. Make sure the dock is in the unlocked position. 2. Angle the front of the GoBook down, toward the front of the dock (where the key and locking mechanism are). Notice the connectors and guide posts (1) near the back of the sled base. These help ensure proper placement of the GoBook. 3.
Chapter 1 Using the MC3 System The PCMCIA slot is on the right side of the GoBook, just below the CD drive. ID 1 Description Front of GoBook XR-1 2 PCMCIA slot 3 CD drive The compact flash card should come installed from the factory. If it is not installed or you wish to replace cards, use the following procedures. To insert the flash card adapter 1. Slide the flash card into the PCMCIA adapter. 2. Open the CD drive / PCMCIA slot compartment on the right-hand side of the GoBook.
Installing the MC3 System 3. Slide the adapter into the PCMCIA slot on the GoBook until it clicks into place. To remove the flash card adapter 1. Open the CD drive / PCMCIA slot compartment on the right-hand side of the GoBook. 2. Push the button in until the adapter pops out of the slot. 3. Pull the adapter the rest of the way out. 4. Remove the compact flash card from the adapter. Mounting the MC3 The MC3 is mounted in a harness that can be attached to either a bucket- or bench-seat in a vehicle.
Chapter 1 Using the MC3 System If you are using a sled to secure the GoBook, be sure to mount the MC3 high enough on the seat that the sled and laptop will fit easily beneath it. If you are using a pedestal mount, the MC3 can be attached lower if desired. To mount the MC3 on the seat 1. If the MC3 radio has been removed from its harness: Slide the radio into its harness, with the MC3 label showing through the opening on the front of the harness.
Installing the MC3 System Sled Systems If you will be installing a sled, be sure to mount the MC3 high enough on the seat back so that the sled and laptop will fit beneath the radio on the seat. Pedestal Systems If you will be attaching the GoBook to a dock on a pedestal, the MC3 radio can be attached lower on the seat. This configuration is shown in the following examples.
Chapter 1 Using the MC3 System Push the free ends of the straps between the seat cushion and the seat back (1), and then extend them up and over the top of the seat back and connect them to the buckles on the top of the vehicle mount (2). 3. Tighten the straps until the MC3 is snug against the seat back.
Installing the MC3 System Connecting the GoBook XR-1 to the MC3 The MC3 rides in a harness that attaches to bucket- or bench-style passenger seat. The sled for the GoBook XR-1 is equipped with a dock for the computer and a junction box for power connectors (the junction box must be attached to the sled prior to use). The sled should be mounted on the seat before the MC3 radio is attached.
Chapter 1 Using the MC3 System MC3 Connectors The top of the MC3 radio contains the power and communications connectors, as well as a fabric and rubber handle used to carry the radio. The connections on the MC3 are described in the following table. ID 1 Connector Vehicle power Description Input that receives the connector running to the vehicle power source to provide power to the MC3.
Installing the MC3 System Connecting the Power Cables Power to the Mobile Collection components is distributed through the junction box on the side of the sled. There are three power cables that must be connected: Vehicle power to the junction box Junction box to the GoBook dock Junction box to the MC3 There is a fourth outlet on the junction box called AUX. It is for powering the EkaNet radio, an optional device for mobile demand reset functionality.
Chapter 1 Using the MC3 System ID 4 Connection (Label) Power in from vehicle (POWER IN) 5 Power out to laptop dock (LAPTOP DOCK) Description Power source input from the vehicle's battery. This connection is hard-wired to the vehicle battery; see the Vehicle Preparation Guide (TDC-0382-xxx) for more information. Connection from junction box to the laptop dock. The laptop dock secures the GoBook in place while you drive a route, and provides power and communication connections for the laptop.
Installing the MC3 System To connect power to the GoBook dock 1. Plug the red and blue end of the cable into the LAPTOP DOCK receptacle on junction box. Pull the silver tab on the power cable back, insert the connector into the junction box, twist the connector so the silver tab lines up with the labeling on the junction box, and release the tab to lock it into place. 2. Plug the pigtail end into the dock connector.
Chapter 1 Using the MC3 System To connect power to the MC3 1. Plug one end of the cable into the RF UNIT receptacle on the junction box. Pull the silver tab on the power cable back, insert the connector into the junction box, twist the connector so the silver tab lines up with the labeling on the junction box, and release the tab to lock it into place. 2. Plug the other end into the POWER IN receptacle on the MC3. Connecting the Antenna Next, connect the omni-mount RF antenna to the radio.
Installing the MC3 System To connect the antenna Connect the omni-mount RF antenna cable to the MAIN ANTENNA connector on the MC3. Be sure to properly tighten the connector; a loose connection can lead to poor radio and read performance. When using older antenna cables with type N connectors along with the MC3 radio, a type N to TNC adapter is required; this adapter is included in the MC3 kit. Attach the adapter securely to both the antenna cable and MC3 to ensure optimal radio performance.
Chapter 1 Using the MC3 System Side-looker antennas attach to the top of the vehicle with several strong magnets. If your vehicle has a fiberglass top, the antennas may not bond securely to the vehicle; Itron does not recommend the use of side-looker antennas with fiberglass-topped vehicles. To connect the side-looker antennas 1. Mount the side-looker antennas (2) on top of the vehicle, two feet in front of or behind the primary RF omni-mount antenna (1). 2. Route the antenna cables into the vehicle.
Installing the MC3 System 3. Remove the caps covering the side-looker antenna ports, identified by R and L on the MC3 radio in the vehicle. 4. Connect the side-looker antenna cables to the R and L antenna inputs on the MC3 radio.
Chapter 1 Using the MC3 System The following picture shows a Mobile Collection system with all the data cables connected. ID 1 2 Connection Description (Label) RF radio antenna RF radio antenna connection on MC3 radio. Receives (MAIN ANTENNA) endpoint signals. GPS antenna (GPS) 3 USB data cable (USB) 4 USB data cable ( 5 ) GPS antenna connection to MC3 radio. Receives GPS signal for vehicle location and tracking. USB data output from MC3 radio.
Installing the MC3 System The USB cable is connected to the dock at the factory and is secured with a cable tie. DO NOT remove this cable tie or unplug the USB cable from the dock. The cable tie helps ensure a secure connection and should never be disconnected. The cable tie also ensures that the correct COM port is used for GPS communications with the Mobile Interface software. Using a different USB port will prevent the MC3 radio from communicating properly with the software. 2.
Chapter 1 Using the MC3 System The Itronix documentation refers to the laptop receptacle as a cradle; Itron uses the term dock to identify this piece of equipment. The term dock is used repeatedly throughout this manual; however, dock and cradle are interchangeable. To attach the GoBook III to the vehicle dock 1. Ensure that the vehicle dock is in the unlocked position. When locked, a steel pin (1) is visible on the top of the vehicle dock; this pin helps secure the GoBook III in place.
Installing the MC3 System 3. Once the GoBook is properly aligned on the vehicle dock, push the locking mechanism in (1) to secure it. This locks the pin in place on the underside of the GoBook and also engages the mounting guides. 4. One end of the USB data cable comes attached to the vehicle dock; attach the other end to the USB port on the MC3. The USB cable is connected to the dock at the factory and is secured with a cable tie. DO NOT remove this cable tie or unplug the USB cable from the dock.
Chapter 1 Using the MC3 System Removing the MC3 System At some point, you may need to remove the Mobile Collection system from the vehicle. Before removing any Mobile Collection system components, be sure to stop the Mobile Interface software, shut down the GoBook, and turn off the vehicle power. See the Mobile Collection User's Guide (TDC-0380xxx) for more information. To remove the GoBook from the vehicle dock 1. Stop processing reads. 2. Complete routes. 3. Export routes. 4.
Removing the MC3 System GoBook XR-1 Push the locking mechanism in and slide it toward the keys on front of the dock (1), and then push it in a little further and pull it back to the starting position to unlock the dock (2). GoBook III Push in underneath the locking mechanism (1) and then pull the handle out (2) as shown. 9. Gently lift the GoBook up and away from the cradle. Disconnecting the Cables Disconnect the cables from the MC3 and leave them in the vehicle for the next installation of the system.
Chapter 1 Using the MC3 System The USB cable (both XR-1 and GoBookIII docks). The power cable that is hard-wired to the dock for GoBookIII installations. 4. Unplug the cables from the sled or pedestal junction box. 5. Release the mounting clips on the MC3 harness and remove the MC3 radio. 6. Unbuckle the seat belt securing the sled to the passenger seat and remove the sled from the vehicle. Leave the pretenstioner attached to the seat belt.
Removing the MC3 System Hardware Installation Guide 29
CHAPTER 2 Using the Mobile Collection 2.x System This chapter describes how to install and use legacy versions of the Mobile Collector radio. If your vehicle has a passenger-side airbag, Itron strongly recommends disabling it when the Mobile collection system is installed. The force of the airbag deploying could damage the laptop, radio, or other components of the system. About the Mobile Collection 2.x System The Mobile Collector 2.
Chapter 2 Using the Mobile Collection 2.x System ID 2 Component Mounting guides Description Hold the GoBook in place, and assist you in placing the GoBook on the radio in the proper location. 3 Flash card reader Provides data backups when configured through the Mobile Administration function. 4 LEDs Indicate system power, operation, and flash card status. 5 Locking mechanism Secures the GoBook to the top of the radio. 6 Screen rests Provide support for the GoBook III screen.
About the Mobile Collection 2.x System Flash Card Reader Route data can be transferred to and from the Mobile Collector using a removable flash card (two CompactFlash® cards are supplied). The Windows operating system on the GoBook recognizes the flash card as a removable drive, allowing standard file access. Periodic data backups to the flash card can be configured in the Mobile Administration application; see the Mobile Collection Administration Guide (TDC-0381-001) or Online Help for more information.
Chapter 2 Using the Mobile Collection 2.x System LED Flash Card Color Green Description Operating normally None System is shutting down or completely off Red Data transferring to/from the flash card reader None System is shutting down or completely off Locking Mechanism The locking mechanism attaches the GoBook to the Mobile Collector. Locking the GoBook to the Mobile Collector reduces the likelihood of the GoBook separating from the Mobile Collector in the event of a collision.
About the Mobile Collection 2.x System ID 1 Connector RF antenna Description Connects to the roof-mounted antenna. See the Mobile Collection Vehicle Preparation Guide. Itron provides a magnetic mount option for the RF antenna. This magnetic mount is intended as a temporary solution and it is for emergency use only. Long-term use of a magnetic mount antenna could adversely affect system performance and is not a supported configuration of this product.
Chapter 2 Using the Mobile Collection 2.x System Mobile Collector Sled The Mobile Collector sled is a mounting bracket designed to secure the Mobile Collector radio in the vehicle and support it and the GoBook in an upright position on the passenger seat. GoBook Mounting Systems There are two mounting options for the GoBook: Direct Mount Option The GoBook mounts directly on the Mobile Collector.
Installing the Mobile Collection 2.x System The GoBook MAX mounts onto the Mobile Collector radio within the mounting guides so that the mounting connector and the external modem connector insert into mating connectors on the underside of the GoBook. A key inserted into the locking mechanism turns clockwise to lock the GoBook in place.
Chapter 2 Using the Mobile Collection 2.x System 2. Lower the Mobile Collector onto the sled and gently move it around until the center pin on the base snaps into the center hole on the underside of the Mobile Collector. 3. While gently applying downward pressure, rotate the collector back and forth slightly until the three pins on the base fit into the three matching holes on the underside of the Mobile Collector. 4.
Installing the Mobile Collection 2.x System When finished, the rear of the Mobile Collector should be flush with the side of the base and its rear connectors should face the passenger door. Connect the Antennas and Power Cables The RF antenna, GPS antenna, and Mobile Collector power cable should be pre-installed in the vehicle and routed to where the Mobile Collector will be installed. The GPS system for version 2.x Mobile Collectors is an optional component that is part of the Mapping system.
Chapter 2 Using the Mobile Collection 2.x System If the power cable does not reach the Mobile Collector, use the optional extension cable to extend the length (extension cables may be purchased from Itron). Plug the power cable into one end of the extension cable and plug the other end of the extension cable in to the Mobile Collector. Be sure both ends snap into their respective connectors. 3. Attach the GPS cable to the connector.
Installing the Mobile Collection 2.x System 2. Angle the top of the GoBook MAX towards the passenger door, as shown below, and lower it so that the two rear connectors (1) on the Mobile Collector top fit into the mating holes on the GoBook MAX underside. 3. Lower the GoBook MAX onto the Mobile Collector within the mounting guides (2) until the underside of the GoBook MAX is flush with the top of the Mobile Collector.
Chapter 2 Using the Mobile Collection 2.x System To attach the GoBook III to the Mobile Collector 1. From the driver’s side of the vehicle, align the GoBook III with the two mounting guides (1) on top of the Mobile Collector. 2. Angle the GoBook III towards the passenger door, as shown below, and slide it under the mounting guides (1) toward the back of the Mobile Collector. 3.
Installing the Mobile Collection 2.x System 8. Lift the GoBook III screen up and gently push it back so that it rests on the Mobile Collector screen rest. Attach the GoBook MAX to the Vehicle Dock As part of an optional remote installation, you may attach the GoBook MAX to a vehicle dock on a pedestal near the driver. The vehicle dock should be pre-installed. Refer to the Itronix Vehicle Cradle Installation Guide for detailed instructions.
Chapter 2 Using the Mobile Collection 2.x System Attach the GoBook III to the Vehicle Dock As part of an optional remote installation, you may attach the GoBook III to a vehicle cradle on a pedestal near the driver. The vehicle cradle should be pre-installed. Refer to the Itronix Vehicle Cradle Installation Guide for detailed instructions. To attach the GoBook III to the vehicle dock 1. Lower the GoBook III onto the vehicle dock. Be sure to align it within the front and read guides on the dock.
Installing the Mobile Collection 2.x System To connect the GoBook III power supply and USB cable 1. Attach the end of the GoBook III power cable (1) to the blue connector on the back of the Mobile Collector radio (2); this connector is located beneath the main power supply. 2. Attach the other end of the power cable to the connector on the back of the GoBook III.
Chapter 2 Using the Mobile Collection 2.x System 3. Plug the USB cable into the Mobile Collector radio by pulling the SMA connector sleeve back, plugging the connector in to the Mobile Collector as shown, and releasing the sleeve. 4. Connect the USB cable to the back of the GoBook III as shown below. 5. Route the USB cable through the channel on the back of the Mobile Collector radio mounting guide. Press the cable down into the channel to make sure it is secure.
Installing the Mobile Collection 2.x System This ensures data communication between the GoBook III and the Mobile Collector radio while you are driving a route. Using the Flash Card in Mobile Collector 2.x Systems You can import route files to the Mobile Interface database and export the collected data using a removable flash card in the Mobile Collector flash card reader. The default drive letter for the flash card reader will vary, depending on the type of GoBook used in your system configuration.
Chapter 2 Using the Mobile Collection 2.x System To insert the flash card 1. Hold the flash card as shown to insert it into the Mobile Collector Flash Card Reader. 2. Insert the card in the flash card reader slot and press it in until it is firmly in place and the eject button pops out. Remove the Flash Card Follow these steps to remove the flash card. Before removing the flash card, shut down the GoBook. Failure to do so could result in data loss on your flash card. To remove the flash card 1.
Removing the Mobile Collection 2.x System Before removing any Mobile Collection system components be sure to stop the Mobile Interface and shut down the GoBook. Unlock and Remove the GoBook Follow these steps to remove the GoBook from the Mobile Collector or vehicle cradle. The following procedure can be used with either the GoBook MAX or GoBook III. To unlock and remove the GoBook 1. Shut down any open applications and then shut down the GoBook. 2. Close the GoBook screen. 3.
Chapter 2 Using the Mobile Collection 2.x System GoBook III Disconnect any cables from the back of the GoBook III. Pull the locking mechanism out, away from the GoBook III. -> If unlocking the GoBook III from the vehicle dock, push up and in on the underside of the locking mechanism, and then pull the mechanism out to release it. 4. Gently lift the GoBook up and away from the Mobile Collector radio or vehicle dock.
Upgrading to a GoBook XR-1 Laptop To remove the Mobile Collector from the sled 1. From the passenger side of the vehicle, reach underneath the top of the base and locate the locking pin knob. 2. Use one hand to pull the knob down, and use the other hand to push a corner of the Mobile Collector in a clockwise direction. 3. Continue pulling the knob down and pushing until the pin can no longer snap into the underside of the Mobile Collector. 4.
Chapter 2 Using the Mobile Collection 2.x System GoBook XR-1 laptop Vehicle docking station Pedestal mounting bracket; pedestal not included Power distribution box; small box with the Itron logo Cables to connect the MC2.5 Radio to the XR-1 docking station and power distribution box (CBA-0269-001, CBA-0332-002, and CBA-0187-004) Peripherals (not pictured): Screen cloth and the USB flash drive To Install the Pedestal Mount 1. Install the pedestal mount between the driver and passenger seats.
Upgrading to a GoBook XR-1 Laptop 2. Place the mount and brackets for the power distribution box in the middle of the pedestal. Tighten securely. 3. Remove the two screws in the top mounting bracket. Top mounting bracket and screws 4. Position the distribution box against the bottom bracket.
Chapter 2 Using the Mobile Collection 2.x System 5. Place the top bracket on the power distribution box and screw the top mounting bracket back in. To Connect the Dock to the Pedestal Mount: Place the vehicle dock onto the pedestal mount and securely tighten.
Upgrading to a GoBook XR-1 Laptop To Mount the XR-1 GoBook to the Docking Station 1. When positioning the XR-1 GoBook onto the dock, put the front end in first. 2. Make sure that the holding bracket is snug against the front and press down on the laptop. 3. Push the locking lever in and to the right to secure the laptop on the dock.
Chapter 2 Using the Mobile Collection 2.x System To Connect to the Power Distribution Box: 1. Use the existing power cable and connect into the Power In slot. 2. Use the CBA-0269-001 cable to connect the power distribution box to the RF unit in the RF Unit slot.
Upgrading to a GoBook XR-1 Laptop 3. Use the CBA-0332-002 cable to connect the power distribution box to the dock in the Laptop Dock slot. vehicle When you are finished, the power distribution box should look like the example below.
Chapter 2 Using the Mobile Collection 2.x System Connecting to the Vehicle Dock 1. Connect the other end of CBA-0332-002 cable to the vehicle dock. This is the smallest of the three cables. 2. Connect the other end of the CBA-0187-004 cable. This cable will come pre-wired to the vehicle dock with a clip to hold the cable in place. Take the other end of the CBA-0187-004 cable and connect it to the RF unit.
Upgrading to a GoBook XR-1 Laptop When you have completed the installation, your hardware should look like the example below.
CHAPTER 3 Using the EkaNet System The EkaNetTM system is an optional component that can be used with the Mobile Collection system. An additional antenna and radio are used to communicate with Eka-equipped endpoints in the field to enable mobile demand reset functionality. This chapter shows you how to install the EkaNet hardware components in a vehicle and then connect them to the Mobile Collection system.
Chapter 3 Using the EkaNet System Laptop GoBook MAX Radio Version MC3 EkaNet Compatible? No GoBook III 2.5 Yes GoBook III MC3 Yes GoBook XR-1 2.5 Yes GoBook XR-1 MC3 Yes About the EkaNet Components The following components are a part of the optional EkaNet system. These components need to be installed in the vehicle. ID 1 Item EkaNet radio Description Routes data received by the antenna to the laptop running the Mobile Interface software, with EkaNet software enabled.
Installing the EkaNet System Installing the EkaNet System Follow the steps below to connect the EkaNet system. To connect the EkaNet system 1. Attach the external EkaNet antenna to the top of the vehicle. It should be placed at least four (4) feet away from the main Mobile Collector RF antenna to prevent interference. This antenna uses a powerful magnet to attach to the vehicle. 2. Using a magnetic-mount antenna on a fiberglass-roofed vehicle is not recommended.
Chapter 3 Using the EkaNet System 3. Insert the EkaNet radio (1) into the pouch (2). The antenna connector (3) must face the top of the pouch. 4. Close the pouch flap over the radio and snap it shut to secure the EkaNet radio. 5. Clip the EkaNet pouch to a harness strap on the back of the seat where the Mobile Collection system is installed. If you are using an MC3 system, clip the pouch to one of the straps that secure the MC3 radio to the seat. This setup is shown in the picture below.
Installing the EkaNet System 6. Connect the EkaNet antenna cable to the top of the radio. Note that in the following example, the pouch and vehicle have been removed for emphasis. 7. Connect the EkaNet power cable to the AUX port on the junction box in your vehicle. If you do not have a junction box in your installation, power will need to be hard-wired from the vehicle's battery to the radio; see your system administrator for assistance.
Chapter 3 Using the EkaNet System Note The Laptop Dock, as shown above, is only used with an MC3 radio. There is not a connected cable attached to the laptop dock with an MC 2.x radio. The Power Junction box, as shown above, is only used with an MC3 radio. For an MC2.x radio, the Power Junction box needs to be ordered to supply power to the EkaNet radio.
Installing the EkaNet System 8. Connect the other end of the power cable to the port on the bottom of the radio. Note that in the following example, the pouch, vehicle, and other cables have been removed for emphasis. 9. Connect the serial cable to COM 1 serial port on the laptop (or dock); this is the end without pins. Be sure to securely connect the cable. For the GoBook XR-1, the serial port is located on the right-hand side of the laptop (9-pin male connector).
Chapter 3 Using the EkaNet System 10. Connect the other end of the serial cable to the bottom of the EkaNet radio; this is the end with pins. Be sure to securely connect the cable. Note that in the following example, the pouch, vehicle, and other cables have been removed for emphasis. When you have finished, the system should look similar to the example below. Removing the EkaNet System When you have finished collecting data with the EkaNet system, you can remove it from your vehicle.
Removing the EkaNet System To remove the EkaNet system 1. Ensure that the vehicle is turned off. 2. Ensure that the GoBook has completed processing reads and is properly shut down. 3. Disconnect the following from the EkaNet radio inside the vehicle: Antenna (connected to the top of the radio and pouch). Power and serial communications cables (located on the bottom of the radio and pouch). 4. Remove the radio and pouch from the vehicle. You can either: Unclip the pouch from the strap it is attached to.
Chapter 3 Using the EkaNet System Leave the clip attached to the strap, but remove the pouch from the clip assembly. To do so, rotate the pouch clockwise 90-degrees (1) and then pull it straight up (2). The clip and strap can remain in the vehicle.
CHAPTER 4 System Maintenance This chapter introduces you to some of the basic maintenance procedures that should be performed regularly to ensure optimal performance of your Mobile Collection system. For more information, see: MC3 Systems Mobile Collection 2.x Systems GoBook Maintenance Antenna Maintenance RF Antenna Maintenance The following procedures should be followed to ensure that the RF omni-mount antenna for your Mobile Collection system is operating properly.
Chapter 4 System Maintenance 2. Remove the gasket (1) from the base (2). 3. Place a new gasket on the base. Push it firmly into place. Ensure that it is level on the antenna base; if it is not level, it could be pinched into the base and damaged when the antenna is reconnected. 4. Reconnect the antenna to the base by turning it clockwise until it is firmly seated on the base. 2.
Service Bulletins Service Bulletins The following information is for customers with legacy Mobile Collection systems in their deployments. The Service Bulletins listed below should have already been shipped to you, along with any required hardware updates, but are included here as a reminder and to help you identify any system components that may need updating. Mobile Collection 2.
Chapter 4 System Maintenance Mobile Collector 2.x Power Adapter (Bulletin Issued September 8th, 2006) In the interest of continuous improvement, Itron has incorporated a reliability upgrade in your Mobile Collector. Reliability of the existing power connector has become the number one cause of Mobile Collector returns during the past year. As a result, we are replacing the existing power connector with a new power connector that has tested to have improved reliability and durability.
Service Bulletins The operation of the new power cable is slightly different from the previous power connector. To engage the new power connector, align the connector tab with the connector slot on the RF unit, insert the connector and then rotate clockwise 45 degrees. To disengage the unit, pull back the locking tab on the cable connector and then rotate the connector 45 degrees counterclockwise.
Chapter 4 76 System Maintenance Hardware Installation Guide
