Installation Guide
Table Of Contents
- CCU100 and Repeater100 Installation Guide
- Important Safety and Compliance Information
- 1 Before You Begin
- 2 CCU/Repeater Basics
- 3 Planning a CCU/Repeater Installation
- 4 Installing the Collector or Repeater
- 5 Battery Care and Maintenance
- A Detailed Collector or Repeater Specifications
- B Port and Protocol Requirements
- C Status and Diagnostics
- D Changing the Repeater Password
- E Antenna Line Sweeps Procedure
- Anritsu Site Master Calibration
- Testing on a Network Device with a Remotely-Mounted 915 MHz Antenna
- Understanding Party Responsibilities
- Itron ChoiceConnect Antenna and Line Sweep Test Form
- Itron ChoiceConnect 915 MHz Antenna Specifications
- Typical Coaxial Cable Specification Summary Table
- Sample Sweeps Output
- F Grounding Specifications
- Understanding Grounding and Bonding
- Exterior Grounding System Design for Concentrators
- Equipment Buried Ground Ring
- Chemical Ground Rod Installation
- Itron Concentrator Equipment
- Installing Coax Ground Kits
- Collector Sites with Indoor Itron TCU / CCU Equipment
- Grounding Rooftop Network Devices
- Down Conductor Installation
- Cold Water Pipe Option
- Building Steel Option
- Antenna and Coax Grounding - Rooftops
- Grounding antennas on rooftops
- Cable Tray Grounding
- Water Tower Grounding
- New Wooden and Concrete Antenna Poles
- Equipment Shelter Grounding
- Repeaters on Communication Tower Sites
- Repeaters on Rooftops
- Multiple Story Site Ground System
- Down Conductors Installation - Building / Shelter Penetrations
- Down Conductors Installation - Limits of Bend Radius
- Down Conductors Installation Connection Methods
- Cable Entrance Facilities
- Clamp-On Ground Resistance Testing
- Understanding Party Responsibilities
Item Description
3 Collector or repeater label
Displays the collector identification number, model number, and other associated information.
4 Power connector
Supplies power to the collector or repeater module. AC mains, DC, or solar power options are
available. A three pin cable connects the collector or repeater to the mains supply. A two pin cable
connects the collector or repeater to a DC supply. A five pin cable connects the collector or
repeater to the solar system.
5 Ground lug
The ground lug is provided on both the CCU and the repeater. Attach the ground lug to earth
ground if there is no ground wire available with the three-conductor power cable, or when you are
using a photocell adapter. This ground helps protect the internal circuitry from high voltage
transient events. The ground lug accepts AWG minimum wire size 14, and maximum wire size 4.
The recommended wire is #10 BTCW.
6 Ethernet
Connects the collector or repeater to the Ethernet backhaul. Also used to connect the collector or
repeater to a router for initial collector setup. Mating weatherproof cables are available from Itron.
These cables are sealed industrial Ethernet circular IP67 connectors (CONEC).
Note A waterproof cap seals the Ethernet port from the elements in the field. Be sure to securely
attach the cap once the collector is installed.
7 Status indicator
This indicator displays the current operational status of the collector or repeater. For more
information, see Status Indicator for more information.
8 Battery Door
Removal of this door allows access to the replaceable battery pack.
* (Not shown)
External GPS antenna connector. This female SMA connector is only on the external antenna
CCU/repeater. Use this connector when mounting the GPS antenna externally.
External WAN antenna connector. This female N connector is only on the external antenna CCU.
Use this connector when mounting the WAN antenna externally.
Local GPS/WAN Antenna System
The external antenna collector or repeater configuration uses a GPS/WAN antenna kit
connected to the collector or repeater by one or two separate pieces of coaxial cable. Cables are
not included in the kit.
■
The WAN antenna is only connected in CCU installations that use a wide area network
backhaul system.
■
The GPS antenna is used in all deployments of this system.
You must install the antennas in a location that allows reception of GPS and WAN signals.
CCU100 and Repeater100 Installation Guide 2 CCU/Repeater Basics
12 February 2021 815-0491-00 Itron, Inc. Page 17 of 133