User's Manual
Table Of Contents
- Foreword
- Important Safety Information
- Contents
- About this Document
- Related Publications
- Product Description
- Features
- Specifications
- Air Interface
- Product Functionality
- Contents
- Integration Goal and Objectives
- Customer Problem Isolation
- Wireline and Wireless Communications
- Design Tips for Serviceability
- Environmental Issues
- Regulatory Requirements
- Contents
- Power Supply
- Host Interface
- Power Management
- Antenna Systems
- Hardware Recommendations
- Battery Selection Criteria
- Contents
- Hardware Integration
- Application Software
- Final Assembly
- Installation
- Troubleshooting
- End User Problem Resolution
- Service Depot Repair
- Contents
- Accessories and Options
- Abbreviations and Acronyms
- Desense Overview
- Desense Measurement Techniques
- Preparing the Device Under Test
- Performance Goals
- Methods of Controlling Emissions
- Antenna
- Summary
- FLEX Application Protocol Licensing
- Licensing
2-6 July 23, 2002
General CreataLink2 XT Hardware Integrator’s Guide
Specifications
Specifications
Table 2-1. General Specifications
Item Specification Specification
Board Kit Number NUF3902 NUF8006
Coding format ReFLEX 50 ReFLEX 25
Serial Protocol CLP or third-party application CLP or third-party application
Operating temperature -40
o
C to +85
o
C -40
o
C to +85
o
C
Interface
22-pin vertical shrouded header for combined
power supply, serial, and parallel I/O interface.
8-pin vertical shrouded header for JTAG
interface; SMA connector for antenna
22-pin vertical shrouded header for combined
power supply, serial, and parallel I/O interface.
8-pin vertical shrouded header for JTAG
interface; SMA connector for antenna
Power supply
requirements
5-12 Vdc, 2.5A minimum, 100 mVpp ripple up
to 5 MHz (worst case estimate if sourcing/
sinking I/O at max values)
5-16 Vdc, 2.5A minimum, 100 mVpp ripple up
to 5 MHz (worst case estimate if sourcing/
sinking I/O at max values)
Backup battery/
alternate transmit
power supply
requirements
3-9 Vdc, 1 mA if used for RAM backup only.
5-9Vdc, 1.4A minimum, 100 mVpp ripple up to
5 MHz if used for transmitter supply (Battery
voltage must be equal to or less than the main
supply voltage)
3-9 Vdc, 1 mA if used for RAM backup only.
5-9 Vdc, 1.4A minimum, 100 mVpp ripple up to
5 MHz if used for transmitter supply (Battery
voltage must be equal to or less than the main
supply voltage)
Physical dimensions
Length: 3.75 in (95.25 mm) Length: 3.75 in (95.25 mm)
Width: 1.75 in (44.45 mm) Width: 1.75 in (44.45 mm)
Height: 0.7 in (17.78 mm) Height: 0.7 in (17.78 mm)
Weight: 1.5 oz. (42.5 grams) Weight: 1.5 oz. (42.5 grams)
Antenna Connector 50 Ohm SMA female connector 50 Ohm SMA female connector
Transmitter specifications:
Frequency 901–902 MHz 896-902 MHz
RF power output (at
antenna port)
0.5W, 0.75W, 1.0W, 1.5W, and 2.0W 0.25W, 0.5W, 1.0W, 1.5W, and 2.0W
Transmit data bit rate 9600 bits per second (bps) 800, 1600, 6400, 9600 bps
Modulation 4-level Frequency Shift Keying (FSK) 4-level FSK
Frequency stability 1 ppm on transmit 1 ppm on transmit
Receiver specifications:
Frequency 940–941 MHz 929-941 MHz
Sensitivity -115 dBm into SMA antenna connector -115 dBm into SMA antenna connector