Operating Procedure and Safety Instructions A WARNING: 1. Read these instructions completely before using the ladder. 2. Failure to comply with all instructions may result in serious injury. 1 DESCRIPTION overproduction. 2 terminology. 3 2 SAFETY «counterproductive .. lll + Proper set-up and use supercargoes product. 3 PUSH KNOB LOCKING HINGE + Hinge operations (adjust angle of ladder) 6 4 SPRING LOADED “J” LOCKS + Lock operation {adjust height) .. 7 5 PROPER USE *Superimposition.
1 DESCRIPTION PRODUCT OVERVIEW The Telescoping Multi ladder is a Industrial grade, mi ult-purpose ladder that can be changed into different positions and working heights. The ladder consists of three sections and two different locking mechanisms. {See Positions 1-4) A\ WARNING serious injury or death. Use ladder only In positions as shown below. Any other position Is misuse of the predict which could result In A caution (Refer to labels on ladder.) DO NOT overload ladder.
WORKING HEIGHTS The following chart shows the working heights of each of the available units in sate of the 4 main positions. £9313-001 MODEL |89317-001 MODEL | 99322001. MODEL | 99326-001. MODEL | Step* 9-4" 1-38 13-2" 15'1" Extension* 14-3" 18-1" 22-0" 25'10" Stair 9-4 1-3 Scaffold* 8-7 9-6 n-5 * Assumes a 5' 6" person with a 12° vertical reach. Ladders extend in one foot increments.
2 SAFETY INSPECTION OF PRODUCT For safety, follow these Inspection Instructions: A WARNING Allure to follow these Instructions could result In serous Injury or death. Always follow these safety Instructions. Never use ladder with missing, worn or + For additional care, use and safety damaged parts. Inspect before each use. instructions, contact your employer « Do not repair damaged ladders without or dealer. authorization.
PROPER SET-UP AND USE (continued) For safety, follow these set-up and use instructions: Never walk, bounce, or move ladder while NOT OVER REACH. Always keep belt buckle between side rails when climbing or working. You may lose your balance and/or tip ladder or scaffold Windy conditions require extra caution. « Use extreme caution when pushing or pulling anything while standing on ladder. Never use ladder as a brace. « The maximum weight of a person, 100s, and materials not to excess duty rating.
3 PUSH KNOB LOCKING HINGE HINGE OPERATION For safety, follow these push knob hinge Instructions: The ladders Inner section allows tha ladder to be folded Into 3 set positions; extension ladder, twin stepladder, and storage. Each of these configurations Is made possible by using the push knob locking hinge located on aah side of the ladder.
4 SPRING LOADED “J” LOCKS LOCK OPERATION For safety, follow these Spring Loaded “J” Locks instructions: The ladders outer sections allow the ladder to telescope and change heights in all the configurations, besides the scaffold mode. Each of these configurations is made possible using the 4 Spring Loaded “J” locks, 2 each on either side. The Spring Loaded “J” locks are operated by pulling straight out and then rotating them away from the holes in the rails.
5 PROPER USE HOW TO SETUP POSITIONS The Telescoping Multi ladder can be used in positions shown below with no additional equipment required. The following instruction will demonstrate how to change the Telescoping Multilayered. Position #1 Twin Stepladder 1) To configure the ladder into the stepladder position, follow the directions for changing the angle of the ladder {Section 3) using the push knob locking hinge. Note: The stepladder position is easiest completed with the ladder standing up.
Position #2 Stairway Stepladder 1) To configure the ladder into the Stairway Stepladder position (this position is used when the user needs to work in a stairway.), configure the ladder in the stepladder configuration as described in potion #1. False to desired height. 2) Lower one ski of the Inner section until the desired step height Is reached. 3) Position ladder on stairway, ensuring all logs are on firm ground or spats. A\ caution « Always face ladder and maintain fim grip while NOT stand on or above t
5 PROPER USE HOW TO SETUP POSITIONS (continued) Position #3 Extension Ladder 75° Note: The extension ladder position is easiest completed with the ladder laying Approximately on the ground. 1) Configuring the ladder Into the extension ladder position, as with the stepladder position, the extension ladder position starts with changing the angle. Note: The push knob hinge will catch in each of the 3 positions.
Position #4 2-Scaffold Base 1) Separate the Inner and outer sections completely by unlocking the “J” locks and sliding tha outer sections off the Inner section. or 2) Place Inner section In stepladder position. This Is the first of two toasties required for the scaffold position. 3) Using both remaining outer ladder sections, turn one section 180 degrees and Insert the “J” locks of one sanction Into the adjacent holes of the other section as shown In Figure 5.
