User Manual

TGMD400A-3 OPERATOR’S MANUAL
7
www.itmtools.com.au
(3) To adjust the quick or slow feeding by feed handle.
(4) To adjust the table left and right travel by table handle wheel.
(5) To adjust the table fore and after travel by table handle wheel.
(6) To operate the spindle handle wheel for micro feed.
(7) To adjust the scale size according to working need.
P
P
R
R
E
E
C
C
A
A
U
U
T
T
I
I
O
O
N
N
F
F
O
O
R
R
O
O
P
P
E
E
R
R
A
A
T
T
I
I
O
O
N
N
Check all parts for proper condition before operation; if normal safety
precautions are noticed carefully, this machine can provide you
withstanding of accurate service.
(1) Before Operation
(a) Fill the lubricant
(b) In order to keep the accurate precision, the table must be free from
dust and oil deposits.
(c) Check to see that the tools are correctly set and the workpiece is set
firmly.
(d) Be sure the speed is not set too fast.
(e) Be sure everything is ready before use
(2) After Operation
(a) Turn off the electric switch.
(b) Turn down the tools.
(c) Clean the machine and coat it with lubricant.
(d) Cover the machine with cloth to keep out the dust.
(3) Adjustment of head
(a) To raise and lower the head, loosen the leaf screw located on the
right side of the raise and lower base. When the desired height is
reached tighten leaf screw to avoid vibration.
(b) Head may be rotated 360°by loosening the same bolts mentioned
above. Adjust the head to the desired angle, then fix the heavy duty
head locknuts, It is tighten the same to fix the head if drilling &milling
too much.
(c) Unscrew 3 nuts while the workpiece needs to be drilled. Turn to the
degrees you wish on the scale, then screw the 3 nuts.
(4) Adjustment of the lifting table
(a) Loosening the locking handles, rocking the crank to move the lifting
table up and down along the column, when arrived the height of your
request, tighten the handles to prevent loose.
(3) To adjust the quick or slow feeding by feed handle.
(4) To adjust the table left and right travel by table handle wheel.
(5) To adjust the table fore and after travel by table handle wheel.
(6) To operate the spindle handle wheel for micro feed.
(7) To adjust the scale size according to working need.
PPRREECCAAUUTTIIOONN FFOORR OOPPEERRAATTIIOONN
Check all parts for proper condition before operation; if normal safety
precautions are noticed carefully, this machine can provide you
withstanding of accurate service.
(1) Before Operation
(a) Fill the lubricant
(b) In order to keep the accurate precision, the table must be free from
dust and oil deposits.
(c) Check to see that the tools are correctly set and the workpiece is set
firmly.
(d) Be sure the speed is not set too fast.
(e) Be sure everything is ready before use
(2) After Operation
(a) Turn off the electric switch.
(b) Turn down the tools.
(c) Clean the machine and coat it with lubricant.
(d) Cover the machine with cloth to keep out the dust.
(3) Adjustment of head
(a) To raise and lower the head, loosen the leaf screw located on the
right side of the raise and lower base. When the desired height is
reached tighten leaf screw to avoid vibration.
(b) Head may be rotated 360°by loosening the same bolts mentioned
above. Adjust the head to the desired angle, then fix the heavy duty
head locknuts, It is tighten the same to fix the head if drilling &milling
too much.
(c) Unscrew 3 nuts while the workpiece needs to be drilled. Turn to the
degrees you wish on the scale, then screw the 3 nuts.
(4) Adjustment of the lifting table
(a) Loosening the locking handles, rocking the crank to move the lifting
table up and down along the column, when arrived the height of your
request, tighten the handles to prevent loose.
Drill protection guard; the machine is provided with a security micro drill guard.
Before pressing the starting push button, set the drill guard in the working
position, otherwise the machine controls will not start.
Note: If the guard is opened when operating the machine, the machine will
stop. Do not remove the guard under any circumstances.