TGD400 GEARED HEAD DRILLING MACHINE OPERATOR’S MANUAL 240v 1 Phase Version: Model # TGD400-1 415v 3 Phase Version: Model # TGD400-3 BEFORE USE, ENSURE EVERYONE USING THIS MACHINE READS AND UNDERSTANDS ALL SAFETY AND OPERATING INSTRUCTIONS IN THIS MANUAL . Serial #............................................ Ver: 1.02 17/03/2022 Date of Purchase............................
TGD400 OPERATOR’S MANUAL LIMITED WARRANTY Industrial Tool & Machinery Sales (hereinafter referred to as ITMS) will, within twelve (12) months from the original date of purchase, repair or replace any goods found to be defective in materials or workmanship. This warranty is void if the item has been damaged by accident, neglect, improper service or other causes not arising out of defects in materials or workmanship.
TGD400 OPERATOR’S MANUAL SAFETY PRECAUTIONS PRIOR TO OPERATION Warning! When using electric tools basic safety precautions should always be followed to reduce the risk of fire , electric shock and personal injury, including but not limited to the following. 1. Power source; ensure that the power source to be used conforms to the power requirements specified on the name plate. Safety - Environment 1. Keep work area clean. Cluttered areas and benches invite injury. 2.
TGD400 OPERATOR’S MANUAL Safety - Peronal 1. Dress properly, do not wear loose clothing or jewellery, they can invite personal injury. Always cover long hair. MACHINE OPERATION 2. When operating power tools suitable personal protective equipment must be worn where necessary, including, but not restricted to eye, ear, respiratory and foot protection. 3. Stay alert, do not use power tools when tired or under the influence of alcohol, drugs or medicine as injury may occur. FIGURE 1 Safety - Operation 1.
TGD400 OPERATOR’S MANUAL SETUP 1. Adjustment of head (a)To raise and lower the head, loosen the nuts located on the right side of the column bracket. Turn the crank on the left side of the column bracket until desired head position is reached. (b)Head may be rotated 360° by loosening the same nuts mentioned above. Adjust the head to the desired angle, then tighten nuts. 2.
TGD400 OPERATOR’S MANUAL MACHINE PARTS - BASE ITEM QTY 1 2 6 7 8 9 10 11 12 31 40 41 42 43 44 45 46 1 1 1 1 1 1 1 1 1 1 4 3 3 1 2 3 2 PART # DESCRIPTION 10002/40H 10001/40H 10016/40H 10014/40 10012/40H 10014/40H 10015/40H 10011/40H 10013/40H base column elevating body column lid locked guide ring up rack low rack guide ring fixed ring Oil cup8 bolt M16X50 screw M10X20 screw M10X20 screw M10X40 bolt M16X190 washer 16 nut M16 ITEM QTY 51 52 53 54 55 56 57 58 59 60 64 65 66 67 68 69 2 2 2 2 2 2 4 8
TGD400 OPERATOR’S MANUAL MACHINE PARTS - HEAD ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 40/1 41 42 43 44 45 46 47 48 49 50 52 53 54 55 56 57 58 QTY PART # DESCRIPTION ITEM QTY 1 1 2 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 1 3 3 1 1 1 1 1 1 4 1 1 2 1 1 2 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 20010B 20011B head body head body cover retaining ring retaining ring airtight base airtight ring motor screw washer plate arbor bolt cov
TGD400 OPERATOR’S MANUAL MACHINE PARTS - HEAD 6 8 www.itmtools.com.
