IS-950R3NPD8 IS -950R3NPD8 Redundant Power Supply ( PS2 Mini- 950W 8 0 P L U S ) SPECIFICATION Revision: 1.0 727 , . Phillips Drive City of Industry. CA 91748. USA http:// www.Xeal.
1. Purpose This specification defines the performance characteristics and functions of a 950+500 watts redundant power supply with Active PFC (Power Factor Correction) and hot swappable capabilities. 2. AC Input Requirements 2.1 Input Voltage and Frequency Voltage (sinusoidal) : 100~240 VAC full range, with 10% tolerance. Input frequency ranges from 47hz~63hz 2.
Duration Surge Operating AC Voltage Line Frequency Performance Criteria Continuous 10% Nominal AC Voltage 50/60 Hz No loss of function or performance 0 - ½ AC cycle 30% Mid-point of Nominal AC Voltage 50/60 Hz No loss of function or performance 3. DC Output Specification 3.1 Output Power / Currents Voltage Table 4: Load Range Minimum Load Maximum Load +3.3V 1A 30A +5V 1A 40A +12V 2A 68A -12V 0A 0.5A +5VSB 0.1 3A Notes: Note 1: The +5 & +3.
requirements. Table 6: Capacitive Loading Conditions 3.4 Output MIN MAX +3.3V 10 12000 Units uF +5V 10 12000 uF +12V 10 11000 uF -12V 1 350 uF +5VSB 1 350 uF Dynamic Loading The output voltages shall remain within the limits specified in Table-Regulation, ripple and noise for the step loading and within the limits specified in Table-Transient Load Requirement for the capacitive loading.
regulation. Tac_on-delay Delay from AC being applied to all output voltages being within regulation. Tvout_holdup Time all output voltage stay within regulation after loss of AC tested at 80% of maximum load. 17 mS Tpwok_holdup Delay from loss of AC deassertion of PWOK tested at 80% of maximum load. 16 mS Tpson_on_delay Delay from PSON# active to output voltage within regulation limits. 5 Tpson_pwok Delay from PSON# deactive to PWOK being deasserted.
3.7 PMBus Function (Optional) FRU Information - Model Name - Electrical Specification Detect and Report Hot-Plug Activities Detect and Report if Power Module is removed/inserted Detect and Report AC Lost/Recovery Detect and Report Redundancy Status Detect and Report Input Voltage/Current/Power Detect and Report Output Voltage /Current/Power Detect and Report FAN RPM FAN Speed Control 3.8 Efficiency 1 The power efficiency under below load conditions: a. 3.3V/25.09A, 5V/33.45A, 12V/56.87A ,-12V/0.
4.3 Voltage Minimum Maximum Shutdown Mode +5V +5.7V +6.5V Latch Off +3.3V +3.9V +4.5V Latch Off +12V +13.3V +14.5V Latch Off +5VSB +5.7V +6.5V Latch Off Short Circuit Protection The power supply shall shut down in latch off mode when the output voltage is short circuit. 4.4 No Load Operation No damage or hazardous condition should occur with all the DC output connectors disconnected from the load. The power supply may latch into the shutdown state 4.
Electromagn etic Interference FCC CFR Title 47 Part 15 Sub Part B EN55022/EN55024 Harmonics IEC61000-3-2 Class D Flicker IEC61000-3-3 ESD Susceptibility EN-61000-4-2 Radiated Susceptibility EN61000-4-3 EFT/Burst EN61000-4-4 Surge Voltage EN61000-4-5 Conducted Susceptibility EN61000-4-6 RF Conducted Voltage Dips and Interruptions Leakage Current 5.
7.Mechanical Overview Dimension: 86(W) x 126.
8.
