Use and Care Manual

ManualsBrandsiSpring ManualsPlumbing SuppliesUltraviolet Whole House Water Filter with Smart Flow Sensor Switch, 55W UV Lamp, 12 GPM

Table Of Contents

iSpring Whole House Ultraviolet Light Water Filter

Installation and Maintenance Manual

Model UVF55FS

Please read the User's Manual Carefully and keep it available

Summary of content (16 pages)

PAGE 1
iSpring Whole House Ultraviolet Light Water Filter Installation and Maintenance Manual Model UVF55FS Please read the User's Manual Carefully and keep it available
PAGE 2
Overview UV has proven to be a quick, reliable, and cost-effective method of water treatment for both point-of-use (POU) and point-ofentry (POE) systems. Being a chemical-free, environmentally friendly, and affordable UV water filter system, iSpring’s upgraded UVF55FS UV water filter can protect the whole house against water concerns commonly found in private wells.
PAGE 3
Components in the Package Model: UVF55FS POE/POU:POE(Point of Entry) Input: 110-120V 50/60Hz UV Bulb: Model#UVB55FS 1.Filter chamber(304SS) 7. UV Lamp 2. Clamps 8. Open-end nut 3. Nut 9. Cover Cap 4. Flow switch 10. UV lamp socket 5. Quartz tube 11. Electronic ballast 6. O-rings 12. Control Switch 13.
PAGE 4
Reminders - Please do not install this product outside or at a place where it is exposed to direct sunlight or freezing temperature. - Please install this product at a place where it is easy to access and maintain. - Avoid jarring/bumping, freezing, overheating and corrosive chemicals.
PAGE 5
Installation Before Installation o o o o o The unit comes with two ports. Both are 1-inch MNPT and can be used as an inlet or outlet. Please choose the correct fittings to fit your plumbing. For easy maintenance, it is recommended that you install an inlet valve and an outlet valve before and after the unit. Please make sure that it can be easily disassembled from the water line for future maintenance.
PAGE 6
Step2–Open the package to check all components inside: Filter Chamber, UV Lamp, Quartz Tube, O-rings, Electronic Ballast, Clamps, Flow switch. Make sure that the Quartz Tube and UV Lamp are clean before installation (clean it with alcohol or mild detergent). Wear soft non-abrasive gloves to keep any finger marks away from them. Step3–Remove both Open and Closed End Nut from filter Chamber. Step4–Install O-ring onto the open end of Quartz Tube (12mm from the edge).
PAGE 7
Step 5–Insert the quartz tube into the Filter chamber. Step6–Install O-ring onto the closed end of the quartz tube. Step8 –Hand-screw open end nut on the filter chamber (open end of quartz tube). To protect the O-ring, do not over tighten. Step7–Hand-screw closed end nut on the filter chamber(closed end of quartz tube). To protect the O-ring, do not over tighten.
PAGE 8
Step 9–Connect 4-pin electrical socket with UV lamp pins tightly. Step 11–Install the cover cap and hand-tighten onto open End Nut. Step10 –Carefully insert the UV lamp into the quartz tube through open end nut. Step 12–Insert the flow switch on the outlet, please notice the water flowing direction.
PAGE 9
Step 13–Connect flow switch cable with control switch, close the switch cover. Step 14–Push control switch to button “AUTO”,the UV lamp will starts working automatically when there only water flowing. Push control switch to button “MOVE”, the UV lamp keep working continuedly. Push control switch button “STOP” to turn off the UV lamp. Mode AUTO is highly recommended to protect the UV lamp.
PAGE 10
Step 15–Select a readily accessible and well lit location to fix the system. The system should always be located close to the point of use and can either be installed horizontally or vertically. Step 16–When all plumbing connections are finished, slowly turn on the water supply and check for leaks. Step 17–Allow the water to run for a few minutes to clear any air or dust that may be in the filter chamber. Step 18–Connect the power for starting up. System Operation Water Quality Guidelines A. B. C. D. E.
PAGE 11
G. The UV system should be installed after the filter on the return line. Always disconnect the water supply and completely drain the water purifier if it will be subjected to temperatures below freezing for extended periods of time. Maintenance - For your safety, ALWAYS wear goggles and turn the power OFF before REPLACING the UV lamp or CLEANING the quartz sleeve!Servicing the unit with power on will also cause damage to the ballast.
PAGE 12
quartz sleeve. Pour vinegar into the water inlet and soak the quartz sleeve until it is clear. Rinse thoroughly and carefully. - The UVF55FS is designed to operate continuously and should not be switched on and off frequently. The UVF11 series come with a flow sensor that turns the UV unit on and off automatically with water flow. - The amount of UV light created by the lamp decreases over time, therefore the lamp should be replaced every 12 months.
PAGE 13
Warranty This Limited Warranty extends to the original purchaser of the system only. This warranty only covers all Manufacturer-supplied items that prove to be defective in material, workmanship, or factory preparation. This warranty covers parts only; all labor is excluded from this warranty, including, but not limited to, services related to the removal, replacement, installation, adjustment, maintenance, and/or repair of the unit or its component items.
PAGE 14
Density Index (SDI) greater than 5.0. In addition, damage to the unit due to fire, accident, negligence, acts of God, or events beyond the control of the Manufacturer are not covered by this warranty.
PAGE 15
Warranty Registration To register your product for the warranty, please visit our website at 123filter.com and go to the “Warranty Registration” tab. We provide a 30-day money back guarantee, a 1-year manufacturer warranty, and lifetime tech support for all of our products. However, we do not have the order information from websites other than 123Filter.com (Amazon, Home Depot, etc.), so please be sure to fill in that information upon registration of your system.
PAGE 16
iSpring Water Systems,LLC Atlanta, Georgia, USA 15