iSpring Ultraviolet Disinfection Sterilizer Water Filter Installation and Maintenance Manual Model UVF11A/UVF11B/UVF11B-E Please read the User's Manual Carefully and keep it available
Table of Content Product Overview------------------------------------------------------------------------------------------------------------------------------------------2 Package Content/Spec and Conditions -------------------------------------------------------------------------------------------------------------------3 Precautions ------------------------------------------------------------------------------------------------------------------------------------------ ------3 Specs and Conditions ------
Product Overview Structure Diagram of Ultraviolet Water sterilizer Quartz Sleeve -2-
Package Content Specs and Conditions Operating Parameters UVF11A/UVF11B/UVF11B-E • • • • • Sterilizer Cylinder body Philips UV lamp, Model#UVB11 Lamp wire connector Ballast with Plug and flow sensor Clamp Clip - 2 pcs Maximum Operating Pressure Minimum Operating Pressure Maximum Ambient Air Temperature Minimum Ambient Air Temperature Maximum Humidity Maximum Hardness Maximum Iron Minimum UVT Installation Rated Flow Rated Service life of the lamp 85psi 4psi 100°F 32°F 100% 120ppm 0.
Installation Model# UVF11A/UVF11B/UVF11B-E Sediments and particles in the water block UV light and serve as shelters for germs. Thus, water coming into the UV sanitizer must be clear (free of particles larger than 20 microns). It is recommended that you install the UV sanitizer after the filters as the last stage. 1) Plug one end of the lamp into the small power socket with green wires.
4) Insert the lamp into the preinstalled quartz sleeve 5) Attach the black rubber cap to the end 6) Insert the stainless-steel UV housing into the clips provided, then mount the UV sanitizer on one of the stages on the filter 7) UVF11A has 2 ports. Either one can be IN or OUT as long as water flow matches the arrow sign on the Smart Flow Sensor. The flow sensor needs to be installed before the inlet. See the water flow direction shown by arrows in the following picture.
Please cut the tubing in an appropriate length to avoid kinking. Please make sure the tubing is fully inserted into the quick-fitting connection about one half-inch deep in order to be sealed by the O-ring at the bottom. 8) Connect the UV transformer to an electrical outlet. 9) Turn on water supply and faucet. Observe the system for any leaks and check if water flow activates the UV light.
- Over time, minerals in the water slowly form a coating on the quartz sleeve. This coating must be removed periodically, as it reduces the amount of UV light reaching the water. Please carefully clean the lamp and quartz sleeve at least 3 times a year if the unit can be unmounted easily. Otherwise, please replace the lamp and quartz sleeve every 1-2 years. - To clean the lamp—Wear rubber, latex or nitrile gloves to avoid contaminating the lamp.
Troubleshooting Symptom Solution The O-ring inside the quartz sleeve might be damaged.
1. The system is to be used with potable water supply only. 2. Feed water pressure to the unit is no less than 4 PSI and no greater than 85 PSI. 3. The system is to be used on water supplies with chlorine concentrations of 1.0 mg/L (ppm) or less. 4. Feed water temperature to the unit must be no less than 32°F and no more than 100°F. 5. Maximum hardness in feed water must be less than 120ppm. 6. Feed water must have a pH between 4 and 8. 7. Turbidity must be less than 1.0 NTU. 8. SDI must be less than 5. 9.
unit will invalidate this Warranty. Should your unit develop a defect or otherwise fail to perform in accordance with this warranty, you should contact the retailer from whom the product was originally purchased. Implied Warranties: The implied at-law warranties of merchantability and fitness for a particular purpose shall terminate on the date one year after the date of purchase. NOTE: IN CASE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, YOU MAY CHOOSE TO RETURN THE SYSTEM.
How To Contact Us Office Hours: Monday-Friday 9:00 a.m. - 5:00 p.m. EST Phone: (678) 261-7611 Email: support@ispringfilter.
