Dear customer, Thank you for purchasing our company’s water purifier. You now have water treatment equipment that is at the world’s leading position in today’s water treatment field. It produces pure water that can be consumed directly so the water you drink is cleaner and also beneficial to your health.
Contents Page Safety Considerations………………………………………………… 3 Product Introduction…………………………………………………… 5 Installation method ……………………………………………..………8 ◆ Pre-Installation Preparations………………………………………..…… 8 ◆ Instructions for Proper Installation……………………………….…….....8 ◆ Installation Notes……………………………………………...…..………11 Troubleshooting Methods…………………………………...………..12 Usage Methods…..…………………………………………………… 12 Maintenance and Upkeep……………………………………..………13 ◆Flushing the RO Membrane…………………………….
Safety Considerations (Be sure to read and remember these safety considerations) In order to avoid harm to you and others or property damage, please make note of the following safety precautions. ★ Ignoring the following safety precautions could result in a risky situation: Warnings If you ignore contents in this section, it may cause permanent damage to the water purifier or cause serious property damage.
Do not use a power source exceeding the machine’s specified value, only use 220V AC power! When installing or repairing, the machine must be disconnected from the power source! The outlet used for the machine’s Otherwise it may lead to electric current must be greater than the shock. machine’s specified value; otherwise it may lead to overheating or fire.
Product Introduction 1. Blown-up profile of the water purifier Diagram 1 2.
3. Water route map Diagram 3 4. Technical parameters Model CR500-A-S-1· Voltage AC 110-240V 50~60HZ Power Rating 120W Suitable Water Pressure 0.1MPa-0.35MPa Operating Pressure 0.5MPa-0.7MPa Inlet Water Temperature 5-38℃ Maximum Inlet Water TDS Value ≤1000PPM Maximum Daily Water Production Volume 500 Gallons, approximately 1892 Liters Standard No.
（2）Second stage: 10-inch granular activated carbon filter Can effectively adsorb free chlorine, humus, disinfection byproducts, smells, discoloration, and other substances in water. （3）Third stage: 10-inch CTO filter Can further remove particles of a smaller size, such as suspended solids and colloids. （4）Fourth stage: side stream reverse osmosis membrane Pore size of 0.0001 microns (0.
(8）With Water Pressure Gauge. Installation Method This company recommends that professionals install the machine for you because you must use drills and other power tools in the process. If you are installing it yourself, please refer to the following steps and diagrams: 1. Pre-Installation Preparations ① Confirm the location the water purifier will be installed (when installing, it should depend on the actual circumstances) ② Confirm that you have the various tools required for installation.
Diagram 4 ② Inlet water 3-way joint and inlet water ball valve installation method Take out the inlet water ball valve from the water purifier accessory box. Wrap one end of the ball valve with the appropriate Teflon tape (see diagram 5). Then screw the ball valve into the corresponding hole of the inlet water 3-way joint (see diagram 6). Take the 6mm hose from the accessories box. Using scissors cut a suitable length of hose. Connect one end of the hose with the inlet water ball valve (see diagram 4).
Stainless steel faucet Main part of faucet Inlet water connection Diagram 7 Diagram 8 ④ Wastewater pipe installation Using a drill, make a φ6.2mm hole into the sink pipe drain. Take out an appropriate length of the 6mm pipe. One end should be inserted into the small hole (see diagram 8). Put some silica gel where the 6mm pipe and the drain pipe connect to prevent leakage. Then, using a cable tie, fix the wastewater pipe to the drain pipe.
Diagram 9 ⑥ Pre-filter installation First take the pre-filter out of the packaging, tear off the packaging of the filters in the order they should be inserted, first is the 5 micron PP filter; second is the granular activated carbon filter, note that the rubber pad must be installed on the top of the activated carbon filter; third is the CTO filter, note that the rubber pad must be installed on the both ends of the CTO filter (See Diagram 10). Diagram 10 3.
Troubleshooting Methods After confirming that the water route connections are correct, confirm that you have a power supply and/or a water supply. Then follow these steps to troubleshoot the machine: Diagram 11 1. Open the tap water inlet water ball valve as well as the water purifier inlet water ball valve, plug in the power (see diagram 11), wait for the filters to fill up water, water will start flowing from the gooseneck faucet. 2.
ball valve is open so the water purifier is in a working condition. Maintenance and Upkeep 1. Flushing the RO Membrane As water passes through the RO membrane, impurities and bacteria are retained on the membrane surface, so you should regularly flush the machine to ensure that the RO membrane performance can achieve the best results. 2. Filter Replacement Time 1. This machine’s filter replacement cycle for the various filters is derived from statistical indicators on average tap water use estimates.
cartridges, remove the old filters, then take the new filters out of the packaging, finally place the filters in the filter cartridges, using the filter wrench, tighten the filter cover. 2.
★ If the water purifier parts are damaged, it is recommended that the water purifier be entrusted to the manufacturer or distributor, service center, or specialized technical personnel for replacement to prevent loss caused by improper operation, the manufacturer is not liable for losses caused by operation or use not in accordance with the instructions and reminders.
After-Sales Service 1. Warranty period: One-year machine warranty. The warranty does not include consumables (consumables include filters, RO membranes). 2. Please keep the warranty in a safe place. For maintenance you must have your purchase invoice, only then is the warranty effective. 3.
