Instruction Manual

Application notes
1. All the receivers in the same zone.
2. Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.
Zone 1
Zone 2
Zone 3
RF remote
30m 30m
Zone 4
RF remote
Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m,
as long as there is a receiver within 30m, the remote control distance can be extended.
Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled
by the same remote, under same dynamic mode and with same speed.
Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range.
Strong signal sources such as WiFi routers and microwave ovens will affect the range.
We recommend for indoor applications that receiver placements should be no further apart than15m.
30m
30m30m
Match Remote Control (two match ways)
Use the controller’s Match key
Match:
Short press match key, immediately press on/off
key (single zone remote) or zone key (multiple zone
remote) of the remote.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
Delete:
Press and hold match key for 5s to delete all match,
The light blinks 5 times means all matched remotes
were deleted.
End user can choose the suitable match/delete ways. Two options are offered for selection:
RGB dynamic mode list
No.
Name
No.
Name
RGB jump
RGB smooth
6 color jump
6 color smooth
Yellow cyan purple smooth
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
1
2
3
4
5
6
7
8
9
10
User Manual Ver 1.0.6
Dual color control
WW=Warm white LED
CW=Cool white LED
Each channel can supply up to 240W@240VAC and white balance can be controlled as such:
Color temperature
Power distribution
Cool white Warm whiteNeutral white
WW=0W,CW=240W WW=120W,CW=120W WW=240W,CW=0W
Dimming curve for RGB/DIM
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60
Brightness(%)
10 20 30 40
Gamma=1.6
Dimming curve for CCT
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.0
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
Cool white(Max. 6500K)
Warm white(Min. 2700K)
Neutral white(4000K)
Recommended CCT range
Linear dual color tuning
70 80 90 100
● S3 connect with single color LED strip
AC110-240V
MAT CH
LN
IN PUT 110- 24 0VA C
OU TPU T
+++
R
G
B
W1
W2
W3
WW
NW
NC
N
High voltage single color LED strip
S3 RGB/CCT/Dimming 3 Channel High Voltage LED Strip Controller
Page 2
High voltage single color LED strip
High voltage single color LED strip
Long press match key 5s, then short press match key 3 times,
The lighting effect will be set to the fade in and fade out in 3s, the indicator light of LED controller blinks 3 times.
Long press match key 10s, restore factory default parameter, the light on/off time restores to 0.5s.
Fade in and Fade out Setting