Assembly Instructions Please visit our website for the most current instructions, assembly tips, report damage, or request parts. All rights reserved. P.
Instruction Manual ! WARNING IMPORTANT INFORMATION MUST READ BEFORE ASSEMBLING PRODUCT - Follow the in formation on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. - Use only a mattress which is 75-76" L x 37.5-38.5"W x 9"H on upper bunk, 75"-76" long and 37.5-38.5"W wide on lower bunk. Replacement Parts--Replacement parts, including additional guardrails, may be obtained from any of our dealers or by contacting us online at our website.
Parts List 6 4 7 14 1 3 15 1 13 14 3 16 14 5 4 3 8 13 2 3 14 9 2 11 12 12 11 10 11 12 12 5 10 All rights reserved. P.
Hardware List A Ø1/4"x15mm Bolt 53 pcs B Ø16mm Small washer 58 pcs C Ø18mm Large washer 3 pcs D Ø5/16"x57mm Bolt 3 pcs E Ø1/4"x32mm Bolt 6 pcs F Washer 6 pcs G Plastic end cap 8 pcs H Plastic tab lock 88 pcs J Plastic link 42 pcs The hardware quantities listed above are required for proper assembly. Some extra hardware may also have been included. All rights reserved. P.
Hardware List K Plastic plug 22 pcs L M4mm Hex key 1 pc M M5mm Hex key 1 pc N Ø1/4"x57mm Bolt 6 pcs The hardware quantities listed above are required for proper assembly. Some extra hardware may also have been included. All rights reserved. P.
All rights reserved. P.
Step 1 1 3 1 2 3 2 4 3 4 5 3 5 Assembly the four support posts by combining parts (2, 3) and (1), then parts (5, 3) and (4) as shown in the illustration. All rights reserved. P.
Step 2 A B A B 4 1 3 3 L 2 5 A B A B 4 1 3 3 2 5 Secure these parts together using screws (A) and small washers (B). Be sure to tighten firmly with hex key (L). All rights reserved. P.
Using bolt (A) secure small washer (B) to part (14) into parts (1,4) , using bolt (A) secure small washer (B) to part (14) into parts (2,5) with hex key (L).
Step 4 12 12 L A 12 B 8 12 9 Attach legs (12) to the lower cross bars using screws (A) and small washers (B) as shown in the illustration. Tighten screws using hex key (L). All rights reserved. P.
Step 5 8 L 9 15 16 A B 5 4 2 1 Attach lower cross bars (8,9) and upper cross bars (15,16) to the end supports in Step 3 using small washers (B) and screws (A) as shown in the illustration. Ensure the slots on the cross bars are facing inward as shown in the illustration. Be sure to tighten all screws firmly using hex key (L). All rights reserved. P.
Step 6 MANUFACTURER LABEL A B L 15 16 1 SAFETY LABEL SAF ET Y LABEL 4 8 2 9 5 Attach another end supports assembled in Step 3 to bed frame using small washers (B) and screws (A) as shown in the illustration. Ensure the slots on the cross bars are facing inward as step 5. Be sure to tighten all screws firmly using hex key (L). Note: Do not tighten all bolts at this step. All rights reserved. P.
Step 7 H 13 15 13 16 8 9 J 13 Insert mattress support bars into the slots on the cross bars as shown in the illustration. Snap plastic tab locks (H) into each slot to lock the mattress support bars in place. Snap plastic links (J) into the middle of the mattress support bars as shown in the illustration. All rights reserved. P.
Step 8 10 F 11 F 11 F F 11 F 10 F E E E E E L E Attach the ladder steps (11) to the ladder support posts (10) using screws (E) and washers (F) as shown in the illustration. All rights reserved. P.
Step 9 1 6 4 B N L B N 15 B N Attach back upper guardrail (6) to the back frame support beams using bolts (A) and washers (B) by hex key (L). Attach guardrail to cross bar (15) using bolts (N) and washers (B) by hex key (L) as shown in illustration。 All rights reserved. P.
Step 10A 7 B N B N B N L C D 10 9 C D B A 10 C D M Attach ladder frame assembly to cross bars (9, 16) using bolts (A, D) and washers (B, C) as shown in illustration. Attach open guardrail (7) to upper cross bar using bolts (N) and washers (B), then attach upper guardrail (7) to support post using bolt (A) and washer (B) as per diagram. Insert bolt (A) to support (4) using hex key (L). Then tighten all the bolts. All rights reserved. P.
Step 11A K K 16 K K K 9 Put plastic plugs (K) into the holes in the front cross bars as shown in the illustration. All rights reserved. P.
Step 12A OPTION A Final All rights reserved. P.
Step 10B 7 B A 10 C D B N C D B N B N L 10 C D M Attach ladder frame assembly to the upper cross bar on the right side using bolt (A) and washer (B) on the left side using bolt (D) and washer (C) as shown in the illustration. Attach ladder support posts to the lower cross bar using bolt (D) and washers (C) as shown in the illustration.
Step 11B K K K 16 9 K K Place plastic plugs (K) into the holes in the front cross bars (9,16) as shown in the illustration. All rights reserved. P.
Step 12B OPTION B Final All rights reserved. P.
Step 14C 4 6 B N 1 15 B N B N L Loosen and remove the back upper guardrail with hex key (L) from the bed frame as per diagram. All rights reserved. P.
Step 15C L A B 16 A M 10 9 Loosen and remove the ladder and open guardrail with hex key (L, M) from the bed frame as per diagram. All rights reserved. P.
Step 16C 4 BA 1 1 BA AB 3 4 3 BA 5 L 3 AB B A L BA 3 2 AB 2 AB 5 Loosen bolts where upper bunk connects with lower bunk . All rights reserved. P.
Step 17C 4 1 1 4 3 3 3 3 5 2 5 2 Lift and separate the bunks. All rights reserved. P.
Step 18C L A 1 B 16 G 12 4 AB G 4 G 15 G 12 A B 1 G G 5 G 2 G 2 5 Attach legs (12) to the upper cross bars (15, 16) using bolt (A) and small washers (B) as shown in the illustration. Tighten bolts using hex key (L). Attach plastic end caps (G) as shown in the illustration. All rights reserved. P.
Place plastic plugs (K) into the holes in the front cross bars as shown in the illustration. Insert bolt (A) to support (1, 2, 4, 5) by using hex key (L).
Step 20C OPTION C Final All rights reserved. P.
