Multipurpose Oscillating Tool Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This oscillating tool is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Ironton Multipurpose Oscillating Tool is a versatile product for home repair, remodeling, and restoration. It’s a detail sander, close-quarter saw, power scraper, and grout removal tool. It’s perfect for trimming door jambs during flooring installation, removing old caulking, taking up vinyl flooring or carpeting, chiseling out door hinges, or trimming cabinets for installation. The tool features a 2.5 amp variable speed motor that delivers 15,000 to 22,000 oscillations per minute.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the tool where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust.
Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. Do not use a product with a malfunctioning switch. Any power tool that cannot be controlled with the power switch is dangerous and must be repaired by an authorized service representative before using.
Grounding ⚠WARNING This machine must be grounded while in use to protect the operator from electrical shock. This unit is equipped with an electrical cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PROVIDED PLUG. If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.
Extension Cords ⚠WARNING USE A PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and cause overheating. Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.
Main Parts of Oscillating Tool Subassembly Quick Change Lever ON/OFF Switch Speed Controller Saw Blade Sand Paper Pads Spade Sanding Pad Holder Before Each Use ⚠WARNING Use suitable devices to locate hidden cables or pipes. Contact with an electric cable may cause an electric shock. Damaging a gas pipe may cause fire or explosion. Damaging a water pipe may cause extensive damage and/or electric shock. Operating Instructions ⚠WARNING To reduce the risk of injury, always wear eye protection.
tool may contact hidden wiring or its own cord. Use auxiliary handles if supplied with the tool. Use the tool only for dry sanding and for cutting dry wood and plastics. Water entering the housing of the electric tool greatly increases the danger of an electric shock. Keep your hands away from the saw blade. Do not reach under the work piece. Touching the saw blade may cause injury. Unit and tools warm up when using them for a long time.
Using the Attachment 1. Lift up the quick change lever (1). 2. Attach the spade (3) to the tool. 3. Lower the quick change lever (1). The attachments can be positioned in a 30° angle to both sides of the tool (e.g., in line with the housing or on the right or left side of the housing).
Speed Controller Turn the speed controller to the desired setting to increase or decrease the speed. The controller can be adjusted from 1 – 6. The speed rate can be changed during operation as well. Maintenance ⚠WARNING Keep the ventilation slots clean and free from debris. Maintain the tool by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used.
Troubleshooting Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance. Failure Possible Cause Cord not connected. Check that cord is plugged in to power source. Internal damage or wear. Have a technician service the tool. Holes on attachment not lined up with pins on spindle. Remove the attachment and re-mount. Attachment dull or damaged.
Parts Diagram Page 14 of 18
Parts List Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Part Description Flange Felt-ring Pin Spindle Seal Ring Circlip for Shaft 28 Spline Spring Washer Bearing 6001 Circlip for Shaft 14 Toggle Block Reducer Limit Ball Screw ST4x27 Spring Sealing Washer Bolt Sealed Cap Cam Wheel Trigger Screw M4x16 Pin Steel Bushing Circlip for Shaft 4 Bearing Washer Sealing Washer Middle Cover Bearing 625 Arm
Part Number 53 54 55 56 Part Description 4.8 Wiring Inserted Connector Tridentate Buckle O-Buckle Tooth Type Gasket ø4.2 Quantity 2 2 1 1 Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
