000 Watt Dual Head Halogen Tripod Worklight Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This light is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use The Ironton 1000 Watt Dual Head Halogen Tripod Worklight is an adjustable halogen shop light. It’s great for painting, plumbing, and all types of repair jobs. This adjustable halogen lamp has a 35-1/2 inch to 71 inch adjustment range. The 45° up-down swivel allows you to shine light anywhere you need it. An extra halogen bulb is included.
Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area. Some of these hazards may be hidden from your view and may cause personal injury and/or property damage if contacted. ⚠WARNING PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating the tool. Do not use the tool while you are tired or under the influence of drugs, alcohol, or medication.
Specific Operation Warnings ⚠WARNING Electric shock hazard. Do not use with an extension cord near water or where water may accumulate. Do not use in wet or damp areas. Electric shock hazard. Do not use while standing on wet or damp areas. Keep lamp at least 16 feet (5m) from pools and spas. Keep plugs and receptacles dry. Use only on GFCI-protected circuits. Do not submerge the light in water. The light is not waterproof. Use extreme caution in any wet location. Burn Hazard.
receptacle installed by a qualified electrician. CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded. Grounded Tools: Tools with 3-Prong Plugs Tools marked with Grounding Required have a 3-wire cord and 3-prong grounding plug. The plug must be connected to a properly grounded outlet.
overheating. Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas. When an extension cord is used with this light, the maximum cord length shall not exceed 50 feet (15.2 m) from where the cord exits the light to the receptacle. Grounded tools require a 3-wire extension cord.
Unfold the bottom base, switch the knob to the desired height, and then tighten. Work light height can be adjusted by loosening the knob (2). Assemble the handle (10) to the H Base (11) by attaching the screws and nuts.
Loosen the screw and nut on the backside, and then take off the glass. Insert the light bulb into the light socket. Repeat this process for the other head.
Attach the work light head to the H Base (11). Insert the screw from downside and then insert the knob (8) and tighten. Repeat the same process for the other work light head. Install the two wire covers (16) by securing the clip with screws. Repeat this process until there are two worklight heads.
Assembly the H Base (11) with two work lights to the tripod stands by screwing the knob (8). Before Each Use ⚠WARNING Always check damaged or worn out parts before using the work light. Broken parts will affect the work light operation. Inspect the general condition of the light.
Cracked or broken parts, and Any other condition that may affect its safe operation. Operating Instructions ⚠WARNING Electric shock hazard. Do not use with an extension cord near water or where water may accumulate. Do not use in wet or damp areas. Electric shock hazard. Do not use while standing on wet or damp areas. Keep lamp at least 16 feet (5m) from pools and spas. Keep plugs and receptacles dry. Use only on GFCI-protected circuits. Do not submerge the light in water.
the light if skin feels warm. Do not look directly at lighted lamp. Oil from skin will drastically shorten the life span of the bulb if not cleaned with rubbing alcohol and allowed to dry before use. Handle the bulb with a soft, clean cloth or clean work gloves. Allow light to cool and wipe external surfaces with a clean cloth. Maintenance ⚠WARNING If the supply cord of this light is damaged, it must be replaced only by a qualified service technician.
When work light is not in use, store it in a secure place, out of the reach of children. Inspect it for good working condition prior to storage and before re-use as needed. Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance. Failure Possible Cause Corrective Action No power.
Parts Diagram Page 16 of 19
Parts List Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Part Description Power Cord Height Adjustment Knob Tripod Receiver Bolt Flat Shaft Lower Tube Middle Tube Knob Handle Handle H Base Upper Tube Light Bulb Reflector Glass Wire Cover Lamp Cover Quantity 1 2 1 1 1 1 1 6 3 1 1 1 2 2 2 2 2 Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of 90 days from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
