Adjustable Waste Oil Drainer Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This oil drainer designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Ironton Adjustable Waste Oil Drainer is ideal for collecting used oil and other automotive fluids. The adjustable oil funnel height allows users to vary the distance between the vehicle oil pan and funnel, minimizing spillage. The container for used oil is not included. Packaging Contents Part A (4) Part B (10) Back Wheel (2) Other Parts (10) Front Wheel (2) Technical Specifications Property Min. Height to Pan Max. Height to Pan Fits Bucket Size Specification 42.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust.
which they are designed. Plan your work, and use the correct product for the job. Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. Do not use a product with a malfunctioning switch. Any power tool that cannot be controlled with the power switch is dangerous and must be repaired by an authorized service representative before using.
Not for use by or around children. Main Parts of Adjustable Oil Drainer Reference 1 2 3 4 5 6 7 Subassembly Back Wheel Front Wheel Base Set Handle Square Tube Clamp Set Oil Pan Oil Pipe Assembly Instructions The numbers in the assembly instructions refer to the parts diagram. You will need a 5mm hex key unless otherwise stated. 1. Attach the fixed front wheels (2) to the base plate (4) by inserting the stub axles into the bushes provided. Secure with 5mm hex socket screws. 2.
3. Slide the clamping set (5) onto the handle (6) and insert the handle into the socket at the rear of the base plate. Secure the handle by tightening the 5mm hex socket grub screw found in the side of the socket on the underside of the base plate. 4. Slide the square tube clamp set (7) into the clamping set (5) and tighten the retaining knob. 5. Slide the oil pipe (10) through the square tube clamp set (7) and tighten the retaining knob.
6. Slide the height selection rings (12) over the bottom end of the oil pipe (10) and lock them into the required position by tightening the two hex sockets grub screws using a 4.5mm hex key. 7. Insert the outlet of the oil pan (9) into the top of the ball valve assembly (8). Ensure that it is fully seated and secure it by tightening the 5mm hex socket screw in the side of the collar. The oil pan is not locked in place and can be rotated 360° as indicated in below picture.
can tilt or fall and cause injury or death. Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. Hot oil can cause severe burns. Allow the engine oil to cool down completely before pumping the oil. Operating Instructions ⚠WARNING Engine exhaust contains carbon monoxide; an odorless, invisible gas that can cause injury or death.
2. The oil drainer has a number of adjustments that allow the drainer to adapt to different sizes of containers and different workshop conditions. The overall height of the unit can be adjusted using a combination of clamps (C) and (E) as shown in Fig1. The centerline of the oil pipe and pan can be adjusted using clamp (F) and the oil pan will rotate 360°. 3.
Parts Diagram Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 12 Part Description Back wheel Front wheel Axes Base set Clamping set Handle Square tube clamp set Ball valve Oil pan Oil pipe Height ring Bolt Page 12 of 15 Quantity 2 2 2 1 1 1 1 1 1 1 1 2
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of 90 days from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
