Datasheet

ManualsBrandsIronridge ManualsSolar & Wind PowerIR-RS-GD-MCL-225

Page 9

support@ | ironridge.com | (800) 227-9523

Parts Catalog

2013 v1.4

Rail Assemblies

Mid Clamps

Mid Clamps are used when top-mounting modules to the top slot of either our Standard (XRS) and/or our Light (XRL)

Rails (ts both). These clamps are not dependent upon the module’s mounting holes. These Mid Clamps may be

ordered with Hex bolts or with T-bolts. Mid Clamps require .25” between modules thus maximizing the total number of

modules per set of rails. Available in clear or black anodized nish.

Item Number Description (Mill Finish) Item Number Description (Black Finish)

29-7000-105 Kit, 4pcs, Mid Clamp A/B/I, 2.00”, Hex 29-7000-105B Kit, 4pcs, Mid Clamp A/B/I, 2.00”, Hex

29-7000-101 Kit, 4pcs, Mid Clamp C/D/J/E, 2.25”, Hex 29-7000-101B Kit, 4pcs, Mid Clamp C/D/J/E, 2.25”, Hex

29-7000-108 Kit, 4pcs, Mid Clamp F/K/G, 2.50”, Hex 29-7000-108B Kit, 4pcs, Mid Clamp F/K/G, 2.50”, Hex

29-7000-104 Kit, 4pcs, Mid Clamp H 2.75”, Hex 29-7000-104B Kit, 4pcs, Mid Clamp H 2.75”, Hex

29-70TB-105 Kit, 4pcs, Mid Clamp A/B/I, 2.00”, Tbolt 29-70TB-105B Kit, 4pcs, Mid Clamp A/B/I, 2.00”, Tbolt

29-70TB-101 Kit, 4pcs, Mid Clamp C/D/J/E, 2.25”, Tbolt 29-70TB-101B Kit, 4pcs, Mid Clamp C/D/J/E, 2.25”, Tbolt

29-70TB-108 Kit, 4pcs, Mid Clamp F/K/G, 2.50”, Tbolt 29-70TB-108B Kit, 4pcs, Mid Clamp F/K/G, 2.50”, Tbolt

29-70TB-104 Kit, 4pcs, Mid Clamp H, 2.75”, Tbolt 29-70TB-104B Kit, 4pcs, Mid Clamp H, 2.75”, Tbolt

Summary of content (5 pages)

PAGE 1
Parts Catalog Rail Assemblies Mid Clamps Item Number Description (Mill Finish) Item Number Description (Black Finish) 29-7000-105 Kit, 4pcs, Mid Clamp A/B/I, 2.00”, Hex 29-7000-105B Kit, 4pcs, Mid Clamp A/B/I, 2.00”, Hex 29-7000-101 Kit, 4pcs, Mid Clamp C/D/J/E, 2.25”, Hex 29-7000-101B Kit, 4pcs, Mid Clamp C/D/J/E, 2.25”, Hex 29-7000-108 Kit, 4pcs, Mid Clamp F/K/G, 2.50”, Hex 29-7000-108B Kit, 4pcs, Mid Clamp F/K/G, 2.50”, Hex 29-7000-104 Kit, 4pcs, Mid Clamp H 2.
PAGE 2
Parts Catalog Rail Assemblies Grounding Mid Clamps Item Number Description (Clear Finish) Item Number Description (Black Finish) RS-GD-MCL-200 Kit, 4pcs, 2.00”, Tbolt RS-GD-MCL-200B Kit, 4pcs, 2.00”, Tbolt RS-GD-MCL-225 Kit, 4pcs, 2.25”, Tbolt RS-GD-MCL-225B Kit, 4pcs, 2.25”, Tbolt RS-GD-MCL-250 Kit, 4pcs, 2.50”, Tbolt RS-GD-MCL-250B Kit, 4pcs, 2.50”, Tbolt RS-GD-MCL-275 Kit, 4pcs, 2.75”, Tbolt RS-GD-MCL-275B Kit, 4pcs, 2.
PAGE 3
Parts Catalog Rail Assemblies End Clamps Item Number Description Item Number Description 29-7000-125 Kit, 4pcs, End Clamp I 1.25” Mill 29-7000-125B Kit, 4pcs, End Clamp I, 1.25” Black 29-7000-134 Kit, 4pcs, End Clamp A 1.34” Mill 29-7000-134B Kit, 4pcs, End Clamp A, 1.34” Black 29-7000-224 Kit, 4pcs, End Clamp B 1.41” Mill 29-7000-224B Kit, 4pcs, End Clamp B, 1.41” Black 29-7000-157 Kit, 4pcs, End Clamp C 1.57” Mill 29-7000-157B Kit, 4pcs, End Clamp C, 1.
PAGE 4
Parts Catalog Rail Assemblies Under Clamps Item Number Description 29-7000-117 Kit, 4pcs, Under Clamp, Clear Under clamps are typically used when it is difficult to access the top of the panel and install a top-down bolted clamp or when you do not want clamps visible from the top. Under clamps can be installed only into the XRS rail and utilizes the upper slot on the back side of the rail. Four (4) clamps are required per panel and replaces end and mid clamps.
PAGE 5
Parts Catalog Rail Assemblies Calculating Rail Length Calculate total required mounting widths as follows: Add module widths + .25” space between modules for mid clamps + 1.5” to each end for end clamping. This formula will provide you with total width of rails. *If rail splices are needed, see page 7. For example, to mount five modules that are each 40” wide, the calculations are as follows: • 5 x 40” = 200” (account for width of modules in portrait mode) • 4 x .