Installation Sheet

SURFACE MOUNTING
You must verify the default position of the ironing board before installing the ironing center. Refer to the Ironing Board
Height Chart below for the proper height of the various installation configurations. Make sure you use the correct model
when selecting your board height. It is recommended a surface mount kit be installed when surface mounting
recessed units.
E-46 E-42
NE-46 NE-42 IAW-42
Ironing Ironing Ironing Ironing
Board Height Board Height Board Height Board Height
Opening Height
Regular Adjusted Regular Regular Adjusted Regular Regular Adjusted Regular
Above Floor
Position Position Position Position Position Position Position Position Position
29" 36" 40" 36" 36"
28" 35" 39" 35" 35"
27" 34" 38" 34" 34"
26" 33" 37" 33" 33"
25" 36" 40" 36"
24" 35" 39" 35"
23" 34" 38" 34"
22" 33" 37" 33"
21"
20"
16" 32" 36"
15" 31" 35"
14" 30" 34"
13" 29" 33"
Note
: The user can adjust height of board after installation of "A" & "U" models with a 4" differential from regular height to a maximum adjusted position.
1. Using a stud finder, locate the wall stud to be used for mounting. Stud should be located as close to the center of cabinet as possible.
2. Locate the existing wiring or other utilities in the wall to prevent drilling into or severing a wire or other utility during installation.
3. Determine the desired location has adequate clearance for ironing. Door opens approximately 180°. Allow at least 16" from side of
cabinet for door to swing open.
AE-46 E-46 AE-42 E-42
ANE-46 NE-46 ANE-42 NE-42 UD-42 IAW-42
Distance from Wall to Tip of Ironing Board 50 1/4" 46 7/8" 50 1/4" 46 7/8" 50 1/4" 43 1/4"
Swivel Clearance from Cutout Opening 16 7/8" 14 5/8" 16 7/8" 14 5/8" 16 7/8" N/A
Distance from Wall in Full Swivel Position 32 1/4" 32 5/8" 32 1/4" 32 5/8" 32 1/4" N/A
Standing Area Clearance * 24" 24" 24" 24" 24" 24"
* The suggested distance from the side of the ironing board where the user typically stands to ensure adequate space for ironing.
4. Using a 3/16" drill bit, pre-drill a pilot hole into the wall stud where the cabinet will be attached to the wall taking care that the
installation height is as desired.
5. Determine the proper mounting screw location inside cabinet so mounting position is located on wall stud as intended. Location for
mounting screw should be as close to the center of the cabinet as possible.
6. Using a 1/4" drill bit, pre-drill hole in the upper and lower cross braces located inside the cabinet as determined in the previous step
taking care that the holes in both braces are drilled to same measurement.
7. Partially start mounting #14 x 4" screw into upper cross brace for installation of ironing center.
8. If installing an electrical model, review Electrical Instructions now (back page.) If installing a non-electrical model, do not install your
own electrical outlet inside cabinet. Warranty voided if independent electrical outlet installed within non-electrical ironing cabinet.
9. Begin installation by carefully lifting the ironing center into position.
10. Attach cabinet to wall by fully inserting the screw in the upper cross brace into the pre-drilled hole in the wall stud.
11. Plumb and level the cabinet. Shim if necessary. Tighten cabinet to wall by fully turning installation screw.
12. Insert second #14 x 4" screw into pre-drilled hole in bottom brace of cabinet and attach to wall making sure cabinet remains
level and square.
13. Decorative trim may be added to cover any irregularity on wall.
Additonal Recommendation: On all adjustable swivel models, locate side ironing board brackets that are secured to the cabinet with
three screws each. Remove the top screw only from each side bracket. Use this location to pre-drill pilot holes into trim. Insert into the
two pre-drilled holes in each side bracket #14 x 1" screws (not included.)
Board Height
Board Height
UD-42
AE-46
AE-42
ANE-46
ANE-42
Ironing
Ironing