i7 / i8 Owner’s Guide
Safety Information Important Safety Information This owner's guide includes information for Regulatory Model(s): RVB-Y1, RVB-Y2 SAVE THESE INSTRUCTIONS WARNING: When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS WARNING: To reduce the risk of injury or damage, read and follow the safety precautions when setting up, using and maintaining your robot.
WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury. EN CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. NOTICE: Indicates a hazardous situation that, if not avoided, could result in property damage. GENERAL WARNING • Your robot is not a toy. Small children and pets should be supervised when your robot is operating. • Do not sit or stand on your robot or charging station.
according to local environmental regulations, or return it to your local authorized iRobot Service Center for disposal. • Charge your robot only with the power supply provided. The provided power supply delivers safety extra low voltage corresponding to the input marking on the robot which is required to maintain safe operation. • To prevent the risk of your robot falling downstairs, ensure that the charging station is placed at least 4 feet (1.2 meters) away from stairs.
About your Roomba® Robot Vacuum Top View Home Base Charging Station TM EN Faceplate RCON Sensor Camera Handle Dust Bin and Filter Light Touch Sensor Bin Release Button Bottom View Brush Caps Dirt Disposal Port* Dust Bin Brush Frame Release Tab Multi-Surface Brushes Cliff Sensor Edge-Sweeping Brush Charging Contacts Cliff Sensor Caster Wheel Cliff Sensor Cliff Sensor Floor Tracking Sensor *Select models only 1 For more information, visit global.irobot.
Using Your Roomba® Robot Vacuum Positioning the Home Base Charging Station TM Charging EN White Light Ring While Charging Good Wi-Fi® Coverage Solid White: fully charged CLEAN Pulsing White: charging Turns off after 1 minute to save power • P lace the robot on the charging station to activate the battery. ote: Your robot comes with a partial charge, but we recommend N that you charge the robot for 3 hours prior to starting the first cleaning job. 4 ft (1.2 m) from stairs 1.5 ft (0.
Cleaning Troubleshooting Remove excess clutter from floors before cleaning. Use your robot frequently to maintain well-conditioned floors. EN Just Press CLEAN Tap to Start / Pause / Resume • Y our robot will tell you something is wrong by playing an audio alert and turning the light ring indicator red. Press CLEAN or tap the bumper for details. Further support and instructional videos are available in the iRobot HOME App.
Accessories Dual Mode Virtual Wall® Barrier* Choose the mode to meet your needs: Virtual Wall Mode: When the switch is in the Virtual Wall position ( ), the device will create a linear barrier to block openings up to 10 feet (3 meters). EN Note: For best results, place at least 8 feet (2.5 meters) from the charging station. Use the Dual Mode Virtual Wall® barrier to keep the robot in the places you want cleaned — and out of the ones you don’t. It creates an invisible barrier that only the robot can see.
Care and Maintenance Care and Maintenance Instructions EN To keep your robot running at peak performance, perform the procedures on the following pages. There are additional instructional videos in the iRobot HOME App. If you notice the robot picking up less debris from your floor, empty the bin, clean the filter and clean the brushes. Part Care Frequency Bin Wash bin as needed Filter Clean once a week (twice a week if you have a pet). Do not wash.
Cleaning the Full Bin Sensors 1 Washing the Bin Remove and empty the bin. Important: Do not wash the filter. Remove the filter before washing the bin. 1 2 2 Wipe the inner sensors with a clean, dry cloth 3 Wipe the bin door with a clean, dry cloth. Closed Door Release the bin, remove the filter, and open the bin door. Rinse the bin using warm water. Cleaning the Edge-Sweeping Brush 1 2 se a coin or small screwdriver U to remove the screw holding the Edge-Sweeping Brush in place.
EN Cleaning the Front Caster Wheel Cleaning the Multi-Surface Brushes 1 1 Pinch the brush frame release tab, lift the tab, and remove any obstructions. 2 Remove the brushes from the robot. Remove the brush caps from the ends of the brushes. Remove any hair or debris that has collected beneath the caps. Reinstall the brush caps. 3 Remove any hair or debris from the square and hexagonal pegs on the opposite side of the brushes.
Cleaning the Sensors, Camera Window and Charging Contacts 1 Wipe sensors, camera window and charging contacts with a clean, dry cloth. iRobot Customer Care USA & Canada If you have questions or comments about your Roomba® robot vacuum, please contact iRobot before contacting a retailer. EN You can start by visiting global.irobot.com for support tips, frequently asked questions and information about accessories. This information can also be found in the iRobot HOME App.
Regulatory Information This device complies with part 15 of the FCC Rules and ICES-003. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada license-exempt RSS standard(s).
WC#: 4632117v4
