Installation Guide

ManualsBrandsIris ManualsGarage Door Opener Parts AccessoriesGD-00Z-1

6. CONTROLLER MOUNTING 7. CONTROLLER CONNECTIONS 8. SYSTEM OPERATION

9. OPERATION NOTES

1. The warning light will ﬂ ash and the warning beeper will sound

ﬁ ve seconds before the door opener is activated. STAY CLEAR

OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO

MOVE!

2. If the door does not completely open or close after remote

activation, the Controller will allow user to try to operate the door

one more time. If the second attempt fails, the Controller will go

into lock-out mode and blink the status indicator. See Note #3.

3. If the status indicator is blinking, the Controller is in lock-out mode

and will not accept remote commands. Activate the door from the

pushbutton wall console then check that the status indicator stops

blinking.

10. TROUBLESHOOTING

PROBLEM

POSSIBLE

CAUSE

CORRECTIVE ACTION

The Controller does

not ﬂ ash or beep

when activated.

No power to

the Controller.

1. Make sure the power supply is

plugged in securely to a live outlet.

2. Make sure the power cord is plugged

in securely to the Controller.

The Controller ﬂ ashes

and beeps when

activated but the door

does not move.

Obstruction

blocking

the door or

incorrect

wiring.

1. Make sure that there are no

obstacles preventing the door from

moving.

2. Make sure that the Controller’s

connection wires are connected

to the proper terminals on the

garage door opener. Trace the

wires from the garage door

opener’s pushbutton wall console

to the door opener. This is where

the Controller’s connection wires

should be connected to.

Garage door opens or

closes, but the status

does not change on

the Iris website or

mobile app.

The tilt sensor

signal is

not being

received by the

Controller.

1. Make sure the tilt sensor is

mounted correctly on the garage

door, with the arrow pointing up.

2. Make sure the battery pull tab has

been removed from the tilt sensor.

3. Replace the battery in the tilt sensor.

LINEAR LIMITED RETAIL WARRANTY

Linear LLC (the Company) warrants to the original purchaser that products delivered hereunder will be

free of defects in materials and workmanship for a period of one (1) year from the date of purchase.

The Company within said period shall at its option, either repair or replace free of charge, any product

or part thereof found, upon the Company’s inspection, to be so defective, and will return the repaired or

replaced product to the purchaser at Company’s expense.

All products returned for warranty service require a Return Product Authorization Number (RPA#).

For warranty service, shipping instructions, and an RPA#, contact Linear Technical Services at

1-855-546-3351. Devices must be sent to the Company at owner’s expense and be accompanied with

statement of defect and proof of purchase.

This warranty is conditioned on the following:

1. The Company must be notiﬁ ed within one year of purchase and have been given the opportunity of

inspection by return of any alleged defective product free and clear of all liens and encumbrances to

the Company or its distributor; and

2. The product must not have been abused, misused or improperly maintained and/or repaired during

such period; and

3. Such defect has not been caused by corrosion or exposure to other than ordinary wear and tear.

THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND

WHATSOEVER INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.

The Company’s maximum liability hereunder is limited to the purchased price of the product. In no event

shall the Company be liable for any consequential, indirect, incidental or special damages of any nature

arising from the sale or use of the product, whether based in contract, tort, strict liability or otherwise.

Note: Some states do not allow limitations on incidental or consequential damages or how long an implied

warranty lasts, so that the above limitations may not fully apply. This warranty gives speciﬁ c legal rights

and you may also have other rights which may vary from state to state.

This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire

de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X22 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2

THE CONTROLLER TYPICALLY

MOUNTS ON THE CEILING

NEAR THE OPENER AND

THE POWER OUTLET

TILT SENSOR

MOUNTED ON

THE TOP PANEL

OF THE DOOR

THE CONTROLLER CAN ALSO BE ATTACHED TO THE OPENER'S

HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET

THE CONTROLER'S WARNING

LAMP MUST BE VISIBLE IN

ALL DOOR POSITIONS

3/16" HOLES

FOR ANCHORS

THE OPTIONAL ADJUSTABLE

MOUNTING BRACKET FITS

3 WAYS ON THE CONTROLLER

THE BRACKET SNAPS ONTO

INDENTS ON EITHER SIDE OR

ON THE END OF THE CONTROLLER

SECURE

BRACKET

WITH SCREW

USE THE FOUR SCREWS

AND ANCHORS TO MOUNT

THE CONTROLLER ABOVE

THE OPENER

INDENT

USE THE BOLTS AND NUTS

SUPPLIED TO ATTACH THE

BRACKET TO A SECURE

STRUCTURE

BE SURE THE CONTROLLER

IS CLEAR OF ALL MOVING

PARTS OF THE GARAGE DOOR

INDENT

PUSHBUTTON

GARAGE

DOOR

OPENER

CONNECT THE CONTROLLER CONNECTION

WIRES TO THE PUSHBUTTON WALL

CONSOLE TERMINALS ON THE GARAGE

DOOR OPENER. THE TERMINALS MAY BE

NAMED "PWC", "WC", "PB", "PUSHBUTTON",

OR "RED AND WHITE". TERMINAL NAMES

AND LOCATIONS VARY BY MODEL.

DO NOT DISCONNECT

ANY WIRES CURRENTLY

CONNECTED TO THE

GARAGE DOOR OPENER !!!

PLUG THE POWER SUPPLY

INTO 115 VAC OUTLET

AND SECURE IT WITH

THE RETAINING BRACKET

BE SURE WIRES ARE

CLEAR OF ALL MOVING

PARTS OF THE GARAGE

DOOR AND OPENER

EITHER WIRE

CAN CONNECT

TO EITHER

TERMINAL

PLUG THE POWER CORD

INTO THE POWER INPUT

JACK ON THE CONTROLLER

FLASH

BEEP

USE THE IRIS WEB SITE AND MOBILE

APPS TO CONTROL YOUR GARAGE

DOOR, VIEW STATUS, AND SET

CUSTOM RULES

THE CONTROLLER WILL ACTIVATE

THE DOOR OPENER AND OPEN

OR CLOSE THE DOOR

STAY CLEAR

OF THE DOOR !!!

THE CONTROLLER WILL BEEP AND

FLASH FOR FIVE SECONDS BEFORE

THE DOOR MOVES

THE IRIS WEB PAGE OR MOBILE

APP WILL SHOW THE NEW STATUS

OF THE DOOR AFTER THE DOOR

COMPLETES ITS CYCLE

NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:

THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS

PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE

www.dtsc.ca.gov/hazardouswaste/perchlorate

KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR.

DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN

ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.

Changes or modiﬁ cations not expressly approved by the manufacturer could void the

user’s authority to operate the equipment.

Les changements ou modiﬁ cations non approuvés expressément par la partie

responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire

fonctionner l’équipement.