Use and Care Guide

ManualsBrandsIris ManualsHome Automation Smart Plug3210-L

SMART PLUG

model

3210-L

lowe’s item #

690407

troubleshooting

Step 1

Begin by unplugging the mod-

ule from the wall receptacle.

Then plug it in again and test

operation. Also, try plugging

the lamp or appliance into a

non-switched wall receptacle to

ensure the lamp works.

Step 2

Unplug any devices from the

module and unplug from the

wall. Now hold the on/o button

while plugging it back into the

wall. Hold the button until the

status LED turns on. Repeat the

“Getting Started” steps to rejoin

the ZigBee network.

for additional help

Check out support.IrisByLowes.

com or call 1-855-469-IRIS (4747).

safety warnings

Each module outlet is rated to 12A

only if the connecting cord is rated

at 90C or greater.

Warnings

• If a load greater than 12 amps is

attached to the output, the Smart

Plug will be damaged and no

longer function.

• The total current limit of the

device is 12A. Do no exceed

this value!

• If a direct short is created on the

output, the Smart Plug will be

damaged and no longer function.

approvals (english)

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

Conforms to FCC Part 15B

Contains FCC ID: T3L-SS011

IC: 12192A-SS011

Industry Canada licence-exempt RSS Standards. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) This device must accept any interference received, including interfer-

ence that may cause undesired operation.

Under Industry Canada regulations, this radio trans mitter may only operate

using an antenna of a type and maximum (or lesser) gain approved for the

transmitter by Industry Canada. To reduce potential radio interference to

other users, the antenna type and its gain should be so chosen that the equiv-

alent isotropically radiated power (e.i.r.p.) is not more than that necessary for

successful communication.

This equipment complies with FCC and IC radiation exposure limits set forth

for an uncontrolled environment. This equipment is in direct contact with

the body of the user under normal operating conditions. This transmitter

must not be co-located or operating in conjunction with any other antenna

or transmitter.

Changes or modiﬁcations not expressly approved by Lowes, Inc. could void

the user’s authority to operate the equipment.

For more information, visit IrisByLowes.com.

approvals (franÇais)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables

aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Conformément à la réglementation d’Industrie Canada, le présent émetteur

radio peut fonctionner avec une antenne d’un type et d’un gain maximal

(ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de

réduire les risques de brouillage radioélectrique à l’intention des autres utili-

sateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance

isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à

l’établissement d’une communication satisfaisante.

Pour plus d’informations, visitez IrisByLowes.com.