Programming Guide

ManualsBrandsIR-TEC ManualsElectronicsPower Pack Unit

CONTROL SCHEME

The following schemes can be programmed via CONTROL setting of the SRP-281. Depending on the connection of wired Low Voltage Occupancy Sensor (LVOS) and

grouped OS-NET Sensor (ONS)/OS-NET Button (ONB), the ON-PPU may control the load in slightly different patterns.

DEVICE LED ACKNOWLEDGEMENT

The device will acknowledge the setting success or failure with following

indications by device LED in BLUE or GREEN. BLUE means the device is

unlinked and GREEN means the device is network linked.

DEVICE LED ACKNOWLEDGEMENT

LED on Control scheme is set to ON/OFF sensing control

Slow blinking (on-off per 0.5 second) Control scheme is set to vacancy sensing control (VSC)

Blinks twice every 2-second Control scheme is set to plug load control (PLC)

Blinks irregularly in BLUE or GREEN Receiving commands from the remote

Fast blinking in BLUE and GREEN

intermittently

Scanning for an open network and linking

Blinks slow once and fast twice The device is under test mode

Blinks slow once and fast once The device is under burn-in mode

Lit for 2 seconds in GREEN Grouping/setting is completed

WIRING DIAGRAMS

Color Description Function Gauge

White

Black

Red

Neutral

Line

Load

switching

Line

voltage

Relay

contacts

AWG

Line Voltage Wires

Color Description Function Gauge

Red

Black

Blue

DC24V

DC-

Sensor

signal input

DC power

supply

Control

24 AWG

Class 2

Low Voltage Wires

Following are basic wiring diagrams for typical controls, consult with an

IR-TEC team member for correct wiring diagram if a more complex control is

required.

A. Occupancy/Vacancy Sensing Control

NOTE: For Vacancy Sensing Control (VSC), at least one OS-NET Button

should be installed and grouped with the ON-PPU-301 to enable

manual-on control.

Black (Line)

White (Neutral)

Red (

Relay)

Red

Black

Green

White

Red (

DC24V)

Black (DC )

Blue (Control)

Red (Relay)

DC+

COM

Occupancy

IR-TEC

Sensor

Load

Line

120/277V

Neutral

Low Voltage

OS-NET Sensor OS-NET Button

NOTE: If PLC is selected, the OFF-command from OS-NET Button will

be ignored.

Black (Line)

White (Neutral)

Red (

Relay)

Red

Black

Green

White

Red (

DC24V)

Black (DC )

Blue (Control)

Red (Relay)

DC+

COM

Occupancy

IR-TEC

Sensor

Low Voltage

Line

120/277V

Neutral

Ground

B. Plug Load Control

OS-NET Sensor OS-NET Button

All line voltage wiring connections should be

made inside of junction box.

To obtain optimal wireless communication,

avoid placing the device behind a metal

mesh/plate.

To enable wireless network control, the

ON-PPU-301 must be grouped and linked with

the other OS-NET devices. An “ungrouped”

ON-PPU-301 with low voltage occupancy

sensor connected will only operate in

standalone control.

LVOS ONS ONB ON-PPU-301 Operations

Load ON

Any LVOS detects occupancy

Load OFF --

√

√ √

√

√√

√ √

√ √ √

Last active LVOS delay elapses

Delay reset

Not activated

Load ON

Any LVOS/ONS detects occupancy

Load OFF -

Both LVOS and ON-PPU delays elapse

Delay reset

When ONS detects occupancy

Load ON

Any LVOS detects occupancy or ONB is pressed ON

Load OFF -

Last LVOS delay elapses or ONB is pressed OFF

Delay reset

When ONB is pressed ON

Load ON

Any ONS detects occupancy

Load OFF --

ON-PPU delay elapses

Delay reset

When ONS detects occupancy

Load ON

Any ONB is pressed ON

Load OFF --

ON-PPU delay elapses or ONB is pressed OFF

Delay reset

When ONB is pressed ON

Load ON

Any LVOS/ONS detects occupancy or ONB is pressed ON

Load OFF

Both LVOS and ON-PPU delays elapse or ONB is pressed OFF

Delay reset

When ONS detects occupancy or ONB is pressed ON

Load ON

Any ONS detects occupancy or ONB is pressed ON

Load OFF -

ON-PPU delays elapse or ONB is pressed OFF

Delay reset

When ONS detects occupancy or ONB is pressed ON

CONTROL = ON/OFF

The load will be switched ON when ON-PPU receives 1) control signal from a wired

LVOS, or 2) wireless command from a grouped ONS/ONB, and switched OFF when

programmed delay time elapses or receives the OFF-command from a grouped OSB.

If the load was switched OFF via an OSB, the ON-PPU will operate in Presentation

Mode. The load will remain OFF if motion is detected before the delay time elapse.

The ON-PPU will resume to auto-ON, auto-OFF control after delay time elapsed.

“

√

” means “one or more units connected/grouped”

LVOS ONS ONB ON-PPU-301 Operations

Load ON

Load OFF - -

Delay reset

Load ON

Load OFF

Delay reset

Load ON

Load OFF -

Delay reset

Load ON

Load OFF -

Delay reset

CONTROL = VSC

VSC refers to Vacancy Sensing Control. This control requires user to turn ON the load

by pressing a grouped OSB, and the ON-PPU will turn OFF the load when delay time

elapses or receives the OFF-command from a grouped OSB.

Any ONB is pressed ON

ON-PPU delays elapse or ONB is pressed OFF

When ONS detects occupancy or ONB is pressed ON

Any ONB is pressed ON

Both LVOS and ON-PPU delays elapse or ONB is pressed OFF

When ONS detects occupancy or ONB is pressed ON

Any ONB is pressed ON

ON-PPU delay elapses

When ONB is pressed ON

Any ONB is pressed ON

Both LVOS and ON-PPU delays elapse or ONB is pressed OFF

When ONB is pressed ON

√

√ √

√ √ √

LVOS ONS ONB ON-PPU-301 Operations

Same as ON/OFF control--

Same as ON/OFF Control-

Load ON Any LVOS detects occupancy or ONB is pressed ON

Load OFF - Last LVOS delay elapses

Delay reset When ONB is pressed ON

Same as ON/OFF control--

Load ON Any ONB is pressed ON

Load OFF -- ON-PPU delay elapses

Delay reset When ONB is pressed ON

Load ON Any LVOS/ONS detects occupancy or ONB is pressed ON

Load OFF Both LVOS and ON-PPU delays elapse

Delay reset When ONS detects occupancy or ONB is pressed ON

Load ON

Any ONS detects occupancy or ONB is pressed ON

Load OFF ON-PPU delay elapses

Delay reset When ONS detects occupancy or ONB is pressed ON

CONTROL = PLC

PLC refers to Plug Load Control. The ON-PPU will enable the plug load power when it

receives 1) control signal from a wired low voltage occupancy sensor, or 2) wireless

command from a grouped OS-NET Sensor/Button, and switch OFF the plug load

power after the area is vacant and programmed delay time elapsed.

√

√ √ √

The DELAY timer of ON-PPU will only be activated by receiving the wireless command

from grouped OS-NET devices.

The ON-PPU will transmit OCC signal wirelessly for group control when wired LVOS

detects occupancy.

To prevent unintentionally shutting off the power for plug load control, ensure to set the

DELAY of the ON-PPU longer than the setting of grouped ONS.

Under PLC mode, all OFF-command from the OS-NET Button will be ignored.

NOTE