Instructions / Assembly

Lamp Adjustment
Twin LED Flood Light can be panned
in 40°and panned out 35°. FIG. 12
Twin LED Flood Light can be tilted
down 67°. FIG. 13
Sensor Head Adjustment
The sensor can be tilted up and
down, as well as rotated left and right.
FIG. 11
Single LED Flood Light can be tilted
down 60°. FIG. 15
Single LED Flood Light can be panned
in 60°and panned out 60°. FIG. 14
FOR MOTION SENSOR LED MODELS:
LM-2401
LM-2402
LM-2403
FOR MOTION SENSOR LED MODELS:
LM-1801
LM-1802
HI level security lighting and LO level accent lighting.
Off : HI-LO feature is off. Works with motion sensor after dark at 100% brightness.
On: At Dusk, light with turn ON at 30% and reduce to 15% in the middle of night.
At Dawn, light will turn off.
For permanent test mode (store test mode): Press and hold the button more than
5 seconds. It will toggle between test mode and normal mode.
- Lights flash 3 times - permanent test mode
- Lights flash 1 time - back to normal
67º
60º
40º
35º
60º
Press once: To learn the current level of outdoor light level and set this as your
"Dusk" level.
Press twice within 5 seconds: Back to factory default setting (+/- 5 lux)
For permanent test mode (store test mode): Press and hold the button more
than 5 seconds. It will toggle between test mode and normal mode.
- Lights flash 3 times - permanent test mode
- Lights flash 1 time - back to normal
ON-TIME:
1 min, 5 min and 10 min. Light stays ON for time set, after motion is no longer
detected.
HI level security lighting and LO level accent lighting.
Off : HI-LO feature is off. Works with motion sensor after dark at 100% brightness.
Press once: To learn the current level of outdoor light level and set this as your
Dusk level.
Press twice within 5 seconds: Back to factory default setting (+/- 5 lux)
DUSK LEARN - FIG. 16
DUSK LEARN - FIG. 17
TIME Adjustment - FIG. 17
(Dusk to Dawn Mode): At Dusk, light will turn On at 30% and reduce to
15% in the middle of the night. At Dawn, light will turn off.
(Timer mode): Seasonally Adjusted Timer: At Dusk, light turns On at 30%
and then shuts Off in the middle of the night hours (calculated automatically by
the hours of darkness).
This is a “Limited Warranty” which gives you specific legal rights. You
may also have other rights which vary from state to state and province
to province.
For a period of three years from the date of purchase, any malfunc-
tion caused by factory defective parts or workmanship will be corrected
at no charge to you. To obtain a refund or a replacement, return the
product to the place of purchase.
NOT COVERED: Repair service, adjustment and calibration due to
misuse, abuse or negligence. Unauthorized service or modification of
the product or of any furnished component will void this warranty. This
warranty does not include reimbursement for inconvenience, installation,
setup time, loss or use or unauthorized service.
This warranty covers only IQ America products and is not extended
to other equipment and components that a customer uses in conjunction
with our products.
This warranty is expressly in lieu of all other warranties, express or
implied, including any warranty, representation or condition of merchant
ability of that the products are fit for any particular purpose or use, and
specifically in lieu of all special, indirect or incidental or consequential
damages.
Repair or replacement shall be the sole remedy of the customer and
there shall be no liability on the part of IQ America for any special,
indirect, incidental or consequential damages, including but not limited
to any loss of business or profit, whether or not foreseeable. Some
states or provinces do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not
apply to you. Retain receipt for warranty claims.
IQ America Three Year Warranty
Customer service number:
For problems or questions, please call us at 1-800-296-1869
Instructions: Please retain this instruction manual for future reference
USING MANUAL OVERRIDE MODE
NOTE: If the power to the
light fixture is off for more
than 5 seconds, allow the
motion sensor to warm up
prior to switching to
manual mode.
Turn the light switch Off
and back On again with
0.2 to 1.5 seconds.
Settings
On-TIME: 1 min, 5 min and 10 min. Lights stay ON for time set after motion is no
longer detected.
HI/LO Light Level Feature - FIG. 17
0116E1
EN
Instruction Manual
MOTION SENSOR LED LIGHTS
LM-1801/LM-1802
LM-2401/LM-2402/LM-2403
On
Manual mode overrides the motion sensor and
“ON-TIME” control so the light will turn ON at full
brightness.
This feature only works at night for 6 hours.
The motion sensor will reset to motion sensing
mode. Manual mode can be toggled on and off
using the light switch.
• To manually turn the lights “ON”, turn the light
switch OFF and back ON again between
0.2 to 1.5 seconds.
• To cancel the manual override mode, turn the
light switch OFF and back ON again between
0.2 to 1.5 seconds. FIG. 18
FIG. 11
FIG. 16
HI/LO Light Level Feature - FIG. 16
FIG. 17
FIG. 12 FIG. 13
FIG. 14 FIG. 15
FIG. 18
TIME Adjustment - FIG. 16
Detection Range:
Motion Sensor Light: Recommended installation height is 8 feet above the
ground. The maximum detection range is about 70 feet. FIG. 9
Note: Walking direction
when performing test.
Walk Test and Adjustment
The walk test is used to test the detection range and to
restrict it if necessary.
• Warm up time is about 60 seconds, then the unit goes
into TEST mode.
The light will turn on for about 2 seconds when
motion is detected.
• After the sensor no longer detects motion for 2 minutes,
then the unit will go into the AUTO sensing mode.
• Note the best way to perform "Walk Test"
is shown in FIG. 10
FIG. 10
180º
8 FEET
up to 70 FEET
240º
8 FEET
up to 70 FEET
FIG. 9
FIG. 8
FIG. 4
Decorative
nuts (06)
LM1801 / LM-2401 LM1802 / LM-2402
Wall mount Eave mount
or
OFF
ON
This package contains:
You will require:
Tools/Equipment need for installation
SUPERIOR ADJUSTMENT VERSATILITY
Dual Mounting Options
Rotate the body up to change from wall mount to eave mount as per drawing
below.
01 X 1
Instruction
Manual
05 X 2
Wire Nuts
06 X 2
Decorative Nuts
07 X 2
Screws
08 X 2
Screws
04 X 1
Connector
Wires
02 X 1
Mounting Bracket
with screws
03 X 1
Gasket
09 X 2
Screws
(M4 X 1.6”)
10 X 2
Screws
(M4 X 1.9”)
WARNING: This equipment has been tested and found to comply with limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and the receiver.
■ Connect the equipment into an outlet on a circuit different from that to which
■ the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
WARNING: “THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONTSTRUC-
TION AND OPERATION OF THE PRODUCT AND THE
HARZARDS INVOLVED”
Installation Procedure:
1. Switch off the power.
2. Thread the shorter set of
two screws (09) included
with the mounting bracket,
through the holes on the
back of the outer bracket.
The threads of the screws
should now be sticking out
of the front of the outer
bracket. FIG. 1
FIG. 5
FIG. 7
FIG. 2
A
H
B
5. Caulk around the edge of the lighting fixture
with silicone sealant to weatherproof around
the junction box (not included). FIG. 5
Note: Make sure all the wires are inside the junction box before attaching the
main body to the junction box.
4. Plug the wire connector (04) into the plug on
the back of the lighting fixture.
Align the body of the lighting fixture over the
mounting bracket screws and mount the
fixture so the screws come through the front
of the light fixture.
Attach the decorative nuts (06) to the screws
and tighten. FIG. 4
3. Insert the house wiring and wire nuts into the
junction box, but make sure the connector
wire (04) is still outside of the junction box.
Attach the gasket (03) to the mounting
bracket (02), so that the mounting bracket
screws go through the gasket (03). FIG. 3
Tighten the mounting bracket screws at the
center of the mounting bracket (see inset C)
Potential high temperature!
Do not touch the metal parts of the device and keep a
minimum distance of 1/2 inch around the floodlight
housing. FIG. 7
Hot Surface Do Not Touch
6. Turn on power.
Conduct walk test to adjust sensor coverage area.
Sensor will be in TEST mode automatically for 2
minutes. Lights will come on for approximately
2 to 3 seconds in TEST mode. FIG. 6
Sensor stays in TEST mode until it no longer senses
motion for more than two minutes, then it will revert
to the AUTO sensing mode.
CAUTION!
Installation Advice:
Since the motion detector reacts to variations in temperature; avoid the following
situations:
WARNING
• Do not aim motion detectors at objects with highly-
reflective surfaces, like swimming pools, mirrors, etc...
• Do not install motion detectors near heat sources
such as heating outlets, air conditioning systems,
dryer vents, lighting fixtures, etc. FIG. 8
• Do not aim the motion detector at objects that
move in the wind, such as tree limbs or bushes,
large plants, etc...
Note: If the mounting bracket screws (09) are not long enough to allow the
decorative nuts (06) to be threaded on them, then you will need to replace the
shorter set of screws (09) with the longer set of screws (10). This is usually due
to the junction box being recessed into the wall.
If the longer mounting bracket screws are necessary, remove the fixture from
the screws, unplug the connector wire, remove the mounting bracket and
replace the mounting bracket screws with the longer screws. Repeat the
installation steps starting with section 2.
Install the mounting bracket (02) with screws (07 or 08)
to the junction box. FIG. 2. Connect the house wires to
the connector wires (04).
Connect the white wire (N) to the white
connector wire and black wire (H) to black
connector wire with wire nuts (05).
Connect the ground wire from the house wiring to
the ground screw on the mounting bracket (02).
• White to white (N)
• Black to black (H)
FIG. 3
Gasket (03)
C
screw (09)
FIG. 1
FIG. 6
150105-US-LM-2401-2402-2403&LM-1801&LM-1802- IM.pdf 1 5/1/2016 9:37:40 AM