Product Manual

14 6.3 USING THE 3-BUTTON REMOTE CONTROL The included remote control(s) is preprogrammed to your MUTT
®
and should never lose
its programming. In the event that you suspect your remote has lost its programming, contact Technical Support at 888-786-7899 or email [e-mail].
HOW TO PROGRAM THE 3-BUTTON REMOTE 1. Press and hold the On/Off Button while turning on the MUTT
®
.
2. Continue to hold for two seconds. 3. Your Remote Control is now programmed.
HOW TO USE THE WIRELESS REMOTE 1. UP ARROW Press and release to select the next circuit in a clockwise rotation. Press and hold for five seconds to activate All Circuits On Mode. 2. DOWN ARROW Press and release to select the next circuit in a counterclockwise rotation. Press and hold for five seconds to turn on hazard lights. 3. ON/OFF Press and release to engage/disengage air brakes. 4. REMOTE CONFIRMATION INDICATOR Press any of the buttons (1, 2, 3) and the blue light (4) will illuminate to confirm the battery power of the remote. NOTE: Inclement weather, nearby power transformers and closely parked trailers may reduce the remote signal. The supplied key fob battery for the remote control is 12V, Alkaline Energizer type A23. A Gold Peak type 23A or Duracell MN21 battery can also be used.
1
4
2
3
3-Button Remote Control
6.4 USING THE 12-BUTTON REMOTE CONTROL The included remote control(s) is preprogrammed to your MUTT
®
and should
never lose its programming. In the event that you suspect your remote has lost its programming, contact Technical Support at 888-786-7899 or email [e-mail].
HOW TO PROGRAM THE 12-BUTTON REMOTE 1. Press and hold the Clearance Button while turning the Trailer Tester’s main power ON. 2. Continue to hold the button for two seconds and then release. 3. Your Remote Control is now programmed. HOW TO USE THE 12-BUTTON REMOTE 1. CIRCUIT SELECTION Pressing these buttons will select the corresponding circuit on the MUTT
®
(Pressing and holding the
ABS/AUX or Brake Light Buttons will latch both circuits on.)
P
R
EV.
CIR
C.
NEXT CIRC.
AI
R BRAKE
S
A
L
L CI
RC.
O
N
HA
Z
A
RDS
AU
TO
C
YLE
A
B
S/A
U
X
LE
FT
T
U
RN
CL
EA
R
A
NCE
T
A
I
L/T
A
G
RIG
HT
TURN
BRA
K
E
L
IG
H
T
12-Button Remote Control
27
PART 9: ABS BLINK CODE DIAGNOSTICS
The MUTT
®
can be used to access ABS Blink Codes on trailers equipped with
ABS systems. Trailers that are equipped with ABS feature an ABS Control Unit (ECU) which detects any electrical fault in the trailer ABS. Most trailers with ABS will also have a dedicated ABS lamp on the driver side. Each fault has a code. When a fault occurs, the ECU stores the code for that fault in its memory. This fault code will be displayed on the trailer ABS lamp when the proper access sequence is engaged.
ACCESSING ABS BLINK/FAULT CODES The MUTT
®
provides a quick method to trigger ABS blink codes without a
tractor present. Depending on the system, you will need to selectively power the Auxiliary and/or Brake Light Circuit in the correct order. Instructions on how to access several of the most common ABS systems can be found below. Once the correct manufacturer’s specifi c sequence is performed, you then must
assess the trailer ABS lamp. The number of blinks displayed on the trailer ABS lamp will correspond to a specifi c ABS fault. As each manufacturer uses different access methods and each blink code has different meanings, the remainder of the ABS section will be broken down by the brand of ABS system installed on the trailer you wish to test. Note: ABS Manufacturer Access Protocols/Blink Codes are subject to change. Please consult specifi c ABS manufacturer manuals for more detailed information and any discrepancies in their literature shall supersede the following directions.