Installation Guide
MDCMR-Guide.doc\4-Sep-03 Page 17 of 20
MDC-TO-RADIO CONNECTION AND SETTINGS
Step 1 Connect the serial cable
(DB9F – DB9M) from the MDC to
the radio.
Step 2 Power up the MDC and the radio.
Step 3 Run the dial-up connection on the MDC
by double clicking on the SLIP2IPMN
shortcut.
Step 4 Create a shortcut for the IPMessage Utility by double
click on the My Computer icon.
Step 5 Double click on the C:\ drive, Program Files,
IPMobileNet, and on the IPMsg folder.
Step 6 Right click on the IPMsg icon and click on Create
Shortcut. Once created, move the shortcut to the
MDC’s desktop for future use.
Step 7 Run the IPMessage Utility by double
clicking on the ‘Shortcut to IPMsg’ icon.
The IPMessage window displays.
Step 8 In the IPMessage window in the left field, enter the
radio’s IP address.
Step 9 In the right field type a ?.
Step 10 Press [ENTER] and the radio configuration displays.
To change the radio’s IP address, perform the following steps:
Step 1 In the right field type UNLOCK=password (enter the
appropriate password) and press [ENTER]. This
unlocks the radio Firmware to enable the IP address
change.
Step 2 In the right field type IPADDRESS=
NNN.NNN.NNN.NNN (replacing the N’s with the new IP
address) and press [ENTER].
Step 3 In the right field type a ? or IPADDRESS and press
[ENTER].
Step 4 Verify that the radio’s IP Addresses is correct.
Step 5 Close the IPMessage window.
DHCP setting for IPMN Mobile Radio without
Ethernet port
For Windows 2000 / XP:
Step 1: Copy file autoipl.txt to PC desktop.
Step 2: Click on Start, Setting, Network and Dial-up
Connections.
Step 3: Right click on SLIP2IPMN.
Step 4: Select Create a copy… to create a copy of
SLIP2IPMN.
Step 5: Select Security, Browse, and Desktop.
Step 6: Select autoipl.txt and click on the OK button to
close.
[From: 172.16.22.2] Host serial = 115200,N,8,1, timeout=200
[From: 172.16.22.2] Host framing = SLIP no status messages
[From: 172.16.22.2] embedded format flag = multiple
[From: 172.16.22.2] Injection = HIGH SIDE, 45MHz
[From: 172.16.22.2] channel spacing = 25000
[From: 172.16.22.2] Channel = 0
[From: 172.16.22.2] TX Power = 0
[From: 172.16.22.2] Car to car TX power = 0
[From: 172.16.22.2] Channel Tx freq Rx freq Inj freq
[From: 172.16.22.2] Frequency=0 , 485.000000, 480.000000, 525.000000
[From: 172.16.22.2] Serial number: undefined
[From: 172.16.22.2] TX quiet time = 5
[From: 172.16.22.2] TX sync time = 12 milliseconds, 0 extra inter-split-frame count
[From: 172.16.22.2] TX tail time = 5
[From: 172.16.22.2] Radio data rate = 19200
[From: 172.16.22.2] Max data tx time = 60 seconds
[From: 172.16.22.2] PLL load to txkey delay = 2 milliseconds
[From: 172.16.22.2] Carrier detect delay time = 3 milliseconds
[From: 172.16.22.2] Polarity = TX-, RX-
[From: 172.16.22.2] allow crc errors = 0
[From: 172.16.22.2] Duplicate time = 10 milliseconds
[From: 172.16.22.2] RSSI step = 12 (=234mV)
[From: 172.16.22.2] noise = -65dBm, -86dBm
[From: 172.16.22.2] Fixed TX Delay = 0 milliseconds
[From: 172.16.22.2] Scale TX Delay = 0 microseconds
[From: 172.16.22.2] IP Address = 172.16.22.2 (VIU = 172.16.21.81, PC = 173.16.23.1)
[From: 172.16.22.2] netmask = 255.255.255.0
[From: 172.16.22.2] num timeslots = 16
[From: 172.16.22.2] timeslot period = 992ms
[From: 172.16.22.2] timeslots per voice packet = 4
[From: 172.16.22.2] 06Feb2036 22:42:41 (PST), calibration=563
[From: 172.16.22.2] diversity speed = 5
[From: 172.16.22.2] receiver = auto
[
From: 172.16.22.2
]
bxri = 0
,
-re
p
lace mdt address
,
-filter out other addresses
,
-filter out kee
p
alive