Installation Instructions
Table Of Contents
- nanoBTS Installation and Test Manual
- 1 Introduction
- 2 Overview
- 3 Customer safety and regulatory information (CENG0133)
- 4 BTS Hardware Installation (CENG0210)
- 5 PSU Installation Guide (CENG0033)
- 6 BTS Installer User Guide (CENG0048)
- Introduction
- 6.2 Capabilities
- 6.3 Concepts
- 6.4 Getting Started
- 6.5 User Interface Reference
- 6.6 The DHCP Server
- 6.7 BTS Attribute Reference
- 6.7.1 The BTS Configuration Dialog box
- 6.7.2 Current Values Display
- 6.7.3 Identifying a nanoBTS
- 6.7.4 How Defaults Work
- 6.7.5 Enabling Configuration Phases
- 6.7.6 The BTS tab
- 6.7.7 The DHCP tab
- 6.7.8 The Unit ID tab
- 6.7.9 The NV Attr (1) tab
- 6.7.10 The NV Attr (2) tab
- 6.7.11 The NV Attr (3) tab
- 6.7.12 The NV Attr (4) tab
- 6.7.13 The Download tab
- 6.8 Using Network Listen
- 6.9 Using BTS Installer via a proxy
- 6.10 Connecting to a nanoBTS via SSL
- 6.11 Configuration File Reference
© ip.access Ltd
COMPANY CONFIDENTIAL CENG0336_XE_nanoBTS_Installation_and_Test_Manual.doc
- 133 -
unitname = FredsBTS ; the unit name to be sent
and if you want the "somewhere" to be sent to the BTS as the location string during
automatic configuration you'll also need:
sendlocation ; send the location string
You might want to put nvram, sendunitname and sendlocation just once in the
[default] section so only the unit name would need to be specified for each
individual BTS.
The SNMP parameters are even more complicated, because to cause one of these to
be sent to the nanoBTS you need to switch on the overall "nvram" boolean parameter
and the specific boolean parameter “sendsnmpconfig” which specifies that some of
the SNMP configuration is to be send and another boolean parameter for each of the
individual SNMP configuration sub-attributes that you wish to send.
Control parameter SNMP sub-attribute affected
SendSnmpCommunityString SnmpCommunityString
SendSnmpTrapAddress SnmpTrapAddress
SendSnmpTrapPort SnmpTrapPort
SendSnmpManagerAddress SnmpManagerAddress
SendSnmpSystemContact SnmpSystemContact
Here is the full list of parameters relating to the non-volatile attribute configuration
phase:
Name Type What
Nvram
Boolean whether to run the non-volatile
attribute setting configuration phase
SendNvConfigFlags
Boolean whether to send the NV
Configuration Flags
F1
Flag NVRAM config flag (see section
6.7.9)
... ... ...
F14
Flag NVRAM config flag (see section
6.7.9)
FstaticInterfaceIpConfig
Flag Synonym for F1
FstaticIpGatewayConfig
Flag Synonym for F2
FstaticVsiConfig
Flag Synonym for F3
Fled
Flag Synonym for F7
FsecondaryOmlEnable
Flag Synonym for F9
FdiagEnable
Flag Synonym for F10
FcliEnable
Flag Synonym for F11
FhttpEnable
Flag Synonym for F12
FpostEnable
Flag Synonym for F13
FsnmpEnable
Flag Synonym for F14
SendPrimaryOmlConfig
Boolean Whether to send the next attributes
PrimaryOmlListLength
Number How many (0, 1 or 2) sets of
primary OML address and port to
send
PrimaryOmlIpAddress
IP address primary OML IP address
PrimaryOmlTcpPort
number primary OML TCP port