Installation Guide
Table Of Contents
- nano3GAP Installation Manual
- 1 Introduction
- 2 Installation Requirements
- 3 nano3GAP Hardware Installation
- 4 Deployment Commissioning of the nano3GAP
- 5 Configuration of the nano3GAP-4 from the OMC-R
- 6 Troubleshooting
- 7 nano3GAP and PSU Regulatory Information
- 8 Appendices
- 8.1 Appendix A - Example AP Configuration File
- 8.2 Appendix B - Licenses and Copyright Notices
- 8.2.1 asn1c
- 8.2.2 bash
- 8.2.3 BusyBox
- 8.2.4 cramfs
- 8.2.5 dropbear
- 8.2.6 glibc
- 8.2.7 gmp
- 8.2.8 ipkg
- 8.2.9 iproute2
- 8.2.10 iptables
- 8.2.11 libcurl
- 8.2.12 libgcc
- 8.2.13 libpcap
- 8.2.14 libxml2
- 8.2.15 Linux Kernel
- 8.2.16 mtd.utils
- 8.2.17 ncurses
- 8.2.18 NTP daemon
- 8.2.19 pcre
- 8.2.20 procps
- 8.2.21 SSL Stack
- 8.2.22 StrongSwan
- 8.2.23 TCL
- 8.2.24 tcpdump
- 8.2.25 thttpd
- 8.2.26 U-Boot
- 8.2.27 zlib
- 8.2.28 General Licenses
nano3GAP Installation Manual Configuration of the nano3GAP-4 from the OMC-R
© ip.access Ltd Page 17
9) Double-click through the tree (Management Views > Configuration Management)
to navigate to the AP to configure.
5.2 Download the Latest nano3GAP-4 Software Image
If the AP already has the latest software version, skip this section.
The latest software image is downloaded to the AP from the OAM File Server. For
instructions about how the software images are uploaded to the OAM File Server, see
[OPM_430].
10)
Make sure that you have the URL to the latest software image file (SDP file)
stored on the OAM File Server.
11) Select the AP in the OMC-R Client.
12) Right-click the AP, select Actions and then Perform Software Download.
13) In the Perform Software Download Actions window, enter the URL of the latest
SDP file.
14) Select whether the image file should be downloaded only, or it should be
swapped with the older image file, and whether the older image file should be
removed from the standby folder on the AP.
15) Click Finish.
The download in progress is indicated by the flashing network LED on the AP.
16) Monitor the 3G AP Admin Package of the AP object in the OMC-R Client.
17) When the standby software version is the version of the downloaded image, right-
click the AP, select Action, and then select Swap Default Software.
18) Right-click the AP object again and then select Reinitialize.
19) Wait for the AP to be shown as connected to the OMC-R.
20) In the 3G AP Admin Package of the AP object, check that the Active Software
Version is that of the new SDP.
5.3 Create an Attribute Configuration File for the AP
The attributes to configure a nano3G-4 AP are stored in a text file. The file can be created
and edited manually in any text editor. For a sample file, see section 8.1.
To create th
e configuration file by using an existing one:
21) Log in to the OMC-R (see section 5.1).
22)
Start the OMC-R Load Attributes Wizard: right-click on any existing AP object in
the OMC-R Client and then select Save Attributes to File.
23) Save the file under a new name.
24) Edit the file in a text editor.