9181078/9303856/9298325 facepalm I RNt Cl or R ) Maintenance Manual (INAPPLICABLE) Important < Please read these instructions: fully before performing any maintenance activities on the bike:
Safety Information Maintenance instruction Adjusting Caliper Brakes o Inspecting and Maintaining the Wheels Changing an liner Tubs .
Important -+ Please read constructionist WARNING! Whiz Bike has been designed assembled and tested in accordance with the HBS EN IS0 8088 standard fo ensure our safety To make sure the bike remains safe i should only be urged for recreational use. Under no circumstances should i be used for competitive coaling. stunting. j Jumping or acrobatic man oeuvres. These types of cycling may resell in serious personal injury and damage to the bike. WARNING! This bicycle is not designed for public roads use.
Antiperspirant Please read these instructions fully Recommended tightening information While assembling the bike It is recommended that where possible 3 forge wrench is used to fight an nuts and bolls. The table below provides a list of torque settings for tha various nuts and bolts.
Adjusting Caliper Brakes Throughout the life of our bike. the front and rear caliber brakes may need disgusting if the brake cable has stretched or the brake ans have been knocked during use. Adjusting the Caliper Cable Tension 1a S 4a. Adjure? the Brake Cable The brake cable must be adjusted to ensure halt the brakes are close as possible {o the wheel nim when no pressure is applied o the brake lever bul still allowing freedom of wheel to rotate.
Inspecting and Maintaining the Wheels it is essential that you regularly Inspect and maintain our wheels especial our bike becomes unstable or vibrates while riding. 1a. Inspect the Truthiness of the Wheels Over the Ifs of the bike . the wheels may begin 1o run out of true, [ 6 they may become wobbled Thesis when the wheal rim moves from side o side. To check the truthiness of a wheal 1At the bike up and spin the wheel I the wheal wobbles iris out of e and will need airing.
Changing an Inner Tube (continued) 1b. Remove the inner Tube from the Tyre Once the Tyre is removed from one side of the wheel rim, carefully remove e imper tube opposites 1o the valve first then remove the valve, 1¢. Replace the Invar Tube into the Tyre Check the inner surfaces of the tire for any sins of damage or foreign matter i e thorns or small stones. Partially inflate the inner tube using a bicycle pump. Carefully feed the nar tube into tha Tyre.
Rear Cable Routing o Breakable ~0 NOTE: This bike is with internal cable routing for rear brake cable. Rear cable goad into top tube table hole 9 aw sax then out via rear of the seat tube »mg There is a seat lube cap cover Q at the back of seat tube. Use dmm Allen Key to loose/lighten bolts Q Cable goes via seat fuse cable hitherto through cable hole on chain stay tube cable hole Q ‘Attach the cable to rear band brake.
Routine Maintenance Schedule Performing routine maintenance correctly on our bike will ensure you get bears of trouble free use. 10 Please keep this manual safe for future reference. It is recommended that the following maintenance schedule is adhered to. This will ensure the bike operates correctly and safe to use.
Before and After Each Ride You should perform the following checks before riding your bike {o ensure i is safe {o use and operating correctly. 1. 1= the Addle Secure? ‘While standing next fo the bilk try 1o move the saddle from side fo side If the saddle moves. you should tightener the seat post boot or the saddle clamps bolts. 2. Are the Front and Rear Tyre Inflated Correctly? Squeeze the sides of tha front and rear treys | they are soft. they will need inflating.
Every Month (continued) 3. Check that the Tyre are in Good Condition Check the outside nf sate types for signs damage including cools, deformation. excessive wear or bald spite. 1 you tray shows any sins of damage it must be replaced immediately. Do not attempt fo ride the bike with damaged treys. 4. Check that the Whee| Spokes are Tia ht. On sate wheel check the tightness of tha spokes This can be done by gently squeezing wo together at time.
