DEAR CUSTOMER Thank you for purchasing the Ionmax Breeze ION420 Air Purifier. The Ionmax Breeze can help to improve the indoor air quality in your home or office. Please read this manual carefully before use to ensure proper usage and save these instructions for future reference.
SAFETY INSTRUCTIONS PLEASE READ ALL THE TIPS AND WARNINGS BELOW BEFORE USING THE AIR PURIFIER. ●● Use only as directed in the User Manual. ●● Do not allow children or persons with reduced physical, sensory, or mental capabilities to operate the unit without adult supervision. ●● Only designed for use in a 220-240V, 50Hz outlet. ●● Use indoors only. ●● Only operate the unit when it is fully assembled. ●● Never touch the unit with wet hands or allow it to come into contact with water.
PRODUCT DIAGRAM SPECIFICATIONS 2 Model Ionmax ION420 Voltage 220-240V, 50Hz Power Rating 55W Coverage Area Up to 35 m2 Germs Killed 99% Noise Level Low: 30dB, Medium: 40dB, High: 50dB Air Flow Low: 65m3/h; Medium: 183m3/h; High: 236m3/h UV Life ≥10,000 Hours Filter Life 12 months (based on typical use) Weight 4.
PURIFICATION SYSTEM Clean Ionised Air Polluted Air 1 2 3 4 5 3-in-1 Filter The Pre-Filter, HEPA Filter and Activated Carbon Filter are combined into one easy-to-change filter. 1. Cleanable Pre-Filter Traps large particles such as human hair, pet dander and dust particles. Helps to extend the life of the HEPA and Activated Carbon filters. 2.
CONTROL PANEL “POWER / UV-C” BUTTON Press this button to turn on or switch off the unit. The UV-C light and Ion generator are also controlled by this button. Note: Ion generator is controlled by the same settings as the UV-C light. “FAN SPEED” BUTTON The fan speed of the unit can be adjusted between Low (I), Medium (II) and High (III) when the unit is in operation.
OPERATING INSTRUCTIONS USING THE APPLIANCE 1. Power / UV-C button Press this button to turn the unit on or off. The Negative Ion generator automatically starts up and shuts down at the same time as the UV-C light. 2. Fan speed button Press this button one or more times to select the desired fan speed. The corresponding fan speed indicator lights up to indicate the current fan speed (Low, Med, High). 3. Timer button Press this button to select the timer settings for 2, 4 or 8 hours.
MAINTENANCE INSTRUCTIONS CLEANING THE UNIT ●● Always unplug the power supply before cleaning the unit. ●● Do not put the unit into water or use water to wash it directly. ●● Do not use any corrosive or flammable detergent to clean the unit. ●● Use a soft cloth with daily cleanser to clean the unit, and make sure the unit is completely dry after cleaning. ●● Regularly clean the inside and surface, to prevent dust from gathering. ●● Regularly clean the air intake and air outlet.
FILTER REPLACEMENT FILTER REPLACEMENT INDICATOR When the “Power” indicator flashes during operation, it indicates that the HEPA and Activated Carbon filters need to be replaced. REPLACING THE FILTERS Follow the Filter Replacement Instructions (page 8) to change the filters. After replacing the filters, with the power off, press and hold the power button for 5 seconds to reset the indicator light. The built-in timer for the filter replacement indicator is 4,320 hours.
FILTER REPLACEMENT INSTRUCTIONS The ION420 comes with the filters fitted inside, but you may need to remove plastic packaging from the filters before the first use of the air purifier. When replacing with new filters, remove all packaging and place filters into the unit as described below. Tip: Place the appliance against a wall for more stability when you remove or insert filters. Note: Make sure you insert the filters in the correct position. Step 1.
Step 5. Place the new Activated Carbon and HEPA filters into the unit, with the HEPA filter facing in and the black Activated Carbon filter facing out. Make sure that the side with the tabs is facing you. Step 6. Place the new pre-filter into the unit. Step 7. To reattach the front panel, insert the bottom hooks into the bottom of the unit first. Then push the panel against the body of the unit.
TROUBLESHOOTING GUIDE Problem Probable Cause Solution Power cable not plugged in Plug in power cable Power cable not plugged in properly Plug in power cable correctly Front cover not attached properly Reattach the front cover Filters not unpacked Unpack the filter packaging (see Filter Replacement Instructions) Too much dust on pre-filter Clean the pre-filter HEPA and Activated Carbon filters dirty Replace HEPA and Activated Carbon filters Abnormal noise Loose parts inside the unit Contact
WARRANTY DETAILS Congratulations on your purchase! It is our aim to provide you with quality products that you can trust. Our products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or a refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
12
WARRANTY REGISTRATION Register your Ionmax Breeze Ion420 online at my.andatech.com.au or fill out this form and forward to the address below with a copy of your proof of purchase. Contact us on 1300 800 200 or visit www.andatech.com.au for options to extend your warranty. Andatech Corporation Pty Ltd PO Box 3038, Nunawading VIC 3131, Australia. Product : Ionmax Breeze Ion420 Date of Purchase : ____________________________________ Place of Purchase : ____________________________________ Serial No.
ionmax.com.au 1300 800 200 Version 1.2. Updated 2.10.
