™ Internal ZipCD ATAPI Drive PC Quick Start PHON ES WRI 650 Re co Re rda Writa ble ble TING DISC IN ! OP CL EN OS E
1 Start your computer, wait for the operating system to load, then insert the ZipCD software disc. ™ Select “Print Installation Instructions” to view and print detailed installation instructions. Select “Install ZipCD Software” to install the software needed for your ZipCD drive. Follow the onscreen instructions.
2 1 2 3 ™ If necessary, change the ZipCD drive jumper setting 1. ™ Leave the setting in the Slave 2 position if you are connecting the ZipCD drive on the same data cable with another device. Use the Master 3 setting if the ZipCD drive will be the only device on the secondary IDE channel. Do not use Cable Select unless your computer supports this mode. (Check your computer documentation.
3 Shut down the computer, disconnect the power cord and remove the cover. CAUTION! Always turn off power to the computer and all devices connected to it before beginning any computer hardware change. NOTE: Locate and write down the drive serial number for your drive.
4 PHO NES Rec ord ReW able rita ble WR ITIN CD 650 G DIS C IN OP EN CL OS E 1 Select the IDE interface connection you want to use. ™ Connect the ZipCD drive to the secondary IDE channel 1 either in slave configuration with another drive as master (e.g. CD-ROM) or in master configuration as the only device. If you are unsure about the connection, refer to the HTML ZipCD drive User’s Manual for more information.
CD 650 CD 650 5 N OPE SE CLO e rdable Recoritabl ReW IN DISC TING WRI ES PHON Locate a vacant 5.25” drive bay. Remove the panel cover and slide the ZipCD drive into the drive bay. ™ Some computers may require rails. Check your computer’s documentation. NOTE: If it makes it easier to connect cables on your computer, you can secure the ZipCD drive in the drive bay now. (See step 9.
6 ZipCD PIN 1 Pin 1 ID E PI N1 T 2 PU +1 IN DCGND +5 ER ST E MA AV SL CT M S LE C LA E SE S BL T CA OU O L DI AU GND R 40 Pin Pin 1 ™ Connect the ZipCD drive to the computer’s IDE connection using an IDE data cable. NOTE: You can use either the cable included with the drive or an IDE cable that may already be connected to the computer’s motherboard. ™ CAUTION! Make sure PIN 1 on the cable connects to PIN 1 on the ZipCD drive, the motherboard, and any other connected device.
7 ID E PI N1 T 2 PU +1 IN DCGND +5 ER ST E MA AV SL CT LE BL E SE CA OUT O L DI AU GND M S C LA S R Skip this step if the computer’s CD-ROM drive is already connected to the computer’s audio in port. ™ Connect the audio cable to the ZipCD drive and the computer’s audio connector, usually located on the sound card or the motherboard. Check your sound card documentation or your system’s documentation and the HTML ZipCD drive User’s Manual for detailed instructions.
8 E ID 1 PIN T 2 PU +1 IN DCGND +5 ER ST E MA LAV T S EC M S L C LA SE S LE B T OU DIO L AU GND CA R Connect a computer power supply cable. You may need a Y-cable if your system’s power cable does not have a free connector. CAUTION! Make sure the power supply cable is securely connected to the ZipCD drive.
9 Secure the drive in the drive bay if needed. If there is not a clear access to the drive bay mounting holes, refer to your computer manual for additional instructions. ™ CAUTION! Mounting screws must not extend into the ZipCD drive more than 6.0 mm (about 0.25 inch).
10 Check all connections, arrange the cables to fit under the cover, and replace the computer cover. Reconnect the power cord, turn on the power switch, and wait for the operating system to load. Because the ZipCD drive is plug-and-play, you will not see “New Hardware Detected” in Windows .
11 ™ Your ZipCD drive is ready to use. Continue reading for help on using your ZipCD drive.
™ Internal ZipCD ATAPI Drive PC Getting Started ™ The ZipCD drive enables you to create CD-R (Compact Disc-Recordable) and CD-RW (Compact Disc-ReWritable) discs. You can write to CD-R discs, but you cannot erase the information on the discs. You can write to and erase information from CD-RW discs up to 1,000 times. Use CD-R discs for audio recordings. Use CD-RW discs for storing data and backing up your work. Some CD-ROM drives and most audio CD players cannot read CD-RW discs.
1 Creating an Audio CD 1 Double-click the Create CD icon on your desktop. 2 Click Audio. 3 Click Audio CD. ™ 4 Insert your music CD into your ZipCD drive. 5 Drag audio tracks from the top window to the bottom CD layout window. 6 If you are copying tracks from multiple CDs, eject the first CD and insert another CD. Repeat step 5. 7 Click the red Create CD button on the top toolbar. 8 Click OK. ™ 9 When you are prompted, insert a blank CD-R disc into your ZipCD drive.
2 Creating a Data CD 1 Double-click the Create CD icon on your desktop. 2 Click Data. 3 Click Data CD. 4 Locate the files you want to copy in the top layout window. 5 Drag the desired files from the top layout window to the bottom CD layout window. 6 Click the red Create CD button on the top toolbar. 7 Click OK. 8 When you are prompted, insert a blank CD-R or CD-RW disc into your ™ ZipCD drive. 9 When the process is complete, click OK.
3 Creating a Backup CD 1 Double-click the Create CD icon on the desktop. 2 Click Data. 3 Click Direct CD. 4 Click Next. ™ 5 Select your ZipCD drive letter. ™ 6 Insert a blank CD-R or CD-RW disc into your ZipCD drive. 7 Wait 10-20 seconds for the disc to be recognized. 8 Click Next. 9 Click Next. 10 Type a label for the disc and click Finish. 11 When the process is complete, click OK. NOTE: The formatting process might take 50-90 minutes for a CD-RW disc.
4 Duplicating a CD ™ 1 Insert the CD you want to copy into the ZipCD drive. 2 Double-click the Create CD icon on the desktop. 3 Click CD Copier. 4 Click the Copy from drop-down box. ™ 5 Select the ZipCD drive letter. 6 Click the Record to drop-down box. ™ 7 Select the ZipCD drive letter. 8 Click the Copy button in the lower right corner of the window. 9 Follow the onscreen directions.
5 ™ For detailed information about the ZipCD drive, view the HTML User’s Manual on the ZipCD software disc. ® To view the User’s Manual on the CD, you must have Microsoft Internet Explorer 3.0 or higher or Netscape Navigator 4.5 or higher installed on your system. One way to locate the User’s Manual on the ZipCD software disc is to right click the CD icon and select Explore, then Docs\index.html.
CE (European Community) Product Name: Iomega Internal ZipCD ATAPI drive ™ Model Numbers: ZIPCD-DVDROM ZIPCD1024int ZIPCDP1024int ZIPCD1536int ™ The Iomega Internal ZipCD ATAPI drive conforms to the following European Directive(s) and Standard(s): Application of Council Directives: 73/23/EEC, 89/336/EEC. Standards to which Conformity is declared: EN60950, EN55022, EN50082-1, EN60825-1. Importer’s Name: Iomega Netherlands branch of Iomega International, S.A.
