Installation Guide

ManualsBrandsInVue Security Products ManualsElectronicsStanding S Pen Recoiler

WARRANTY - APPLICABLE TO ALL PARTS SHOWN

InVue warrants that if, within one (1) year of purchase, should there be a defect in material or workmanship,

and if, in the judgment of InVue, the product has received normal use and care, and if no damage or wear

has resulted from abuse, neglect, misuse, tampering, or accident, the product will be repaired or replaced

free of charge, as determined by InVue in its sole discretion. All claims of defects shall be made in writing

no later than ten (10) business days after discovery thereof. THIS WARRANTY IS MADE IN LIEU OF ALL

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PURPOSE. ALL OTHER WARRANTIES ARE

EXCLUDED. The product is not a sale of consumer goods and is for commercial or business use only.

INVUE’S ONLY OBLIGATION SHALL BE TO REPAIR OR REPLACE SUCH PRODUCTS PROVED TO BE DE-

FECTIVE. INVUE SHALL NOT IN ANY WAY BE LIABLE EITHER IN TORT OR IN CONTRACT FOR ANY LOSS

OR DAMAGE, DIRECT OR INCIDENTAL, OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY

TO USE THE PRODUCTS. IN NO EVENT SHALL INVUE’S LIABILITY EXCEED THE PURCHASE PRICE OF

ANY PRODUCT.

www.invue.com

For after sale service, please see contact information below for

InVue Customer Support globally or visit our website here.

If you encounter an issue accessing the link for VOC or A/S,

please try https://invue.com/contact-information.

When registering the VOC or A/S request, please describe the

symptom or issue as clearly as possible.

NA / LATAM // 704.752.6513

•

888.55.INVUE

APAC // +852.3127.6811

EMEA // +31.23.8900150

SD0705 Rev3 10/21/19

Insert the pin fob tool into the

hole next to the cable.

Part 3: Removal

Unplug the power supply from

the outlet.

Use the scraper removal

tool (DNTX93) to break the

adhesive bond between the

recoiler and xture.

Slide the sleeve off the pen

and separate the upper and

lower halves of the stylus clip.

Pivot the fob tool back to

remove the retainer.

Note: Be careful not to lose

the clip when removing.

PMN: STANDING S PEN RECOILER

FCC ID: 2AFR8F1754B

IC: 23313-F1754B

FCC WARNING STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This device complies with Part 18 of the FCC rules.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accoradance with the instructions, may cause harmful interfernce to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT

(Wireless Charger Dock)

This equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other

antenna or transmitter. This equipment should be installed and operated with a minimum distance of 15cm surrounding the device and 20 cm above the top surface of the device.

IC WARNING STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

IC RADIATION EXPOSURE STATEMENT

(Wireless Charger Dock)

This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other

antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Cet équipement est conforme aux limites établies par

Industrie Canada en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Cet appareil etson antenne ne doivent pas être colocalisés ou fonctionner en conjonction avec tout

autre antenne ou émetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.