InvizBox User Guide | Version 1.3 InvizBox User Guide InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.
InvizBox User Guide | Version 1.3 Introduction InvizBox is a small, low power device that helps provide an easytouse method of protecting your privacy on the Internet. Just plug the InvizBox into your existing router / modem. A new "InvizBox" wifi hotspot will appear. Connect to the new hotspot and follow the one time configuration setup and you're ready to go! All devices that you connect to the InvizBox wifi will route their traffic over the Tor Privacy Network.
InvizBox User Guide | Version 1.3 Quick Setup In this section we will show you how to quickly setup the InvizBox in 6 easy steps. Six Easy Steps 1. Connect the supplied ethernet cable to the WAN port on the InvizBox. 2. Connect the other end of the ethernet cable to an ethernet port on the router given by your internet service provider. 3. Connect the USB cable to a suitable power source.(Note: Many routers now have suitable USB ports which can be used instead of a separate power supply) 4.
InvizBox User Guide | Version 1.3 Overview To access any of the admin pages outlined point your browser to : http://10.101.0.1 General Status The Overview page gives you a brief overview of a number of things: ● Tor Status ● Time, Date and other system information ● Network Overview ● DHCP Status ● Connected Clients Below is a screenshot of how it will look InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 Admin Password & Language This section allows you to change the password for UI and SSH, along with the language of the UI. InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 To change Password just enter in the new password into both Boxes and click “Save & Apply” at the bottom of the screen. To Change language, Select the language from the dropdown and click “Save & Apply” at the bottom of the screen. DropBear SSH This section describes how to setup SSH access to the InvizBox. Out of the box, SSH is disabled. To enable SSH you have to click “Add”. Once that is done to can configure the options as seen below.
InvizBox User Guide | Version 1.3 Here you can configure the port and other options displayed. You can also add SSHKeys (one per line) into the appropriate section. Once you change any of these click the “ Save & Apply” button at the bottom of the screen. Network Wifi The WIFI section allows you to go deeper and configure the wifi access point to your own setup. Ideally it is only recommended to change the wifi E SSID, access point password and channel. InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 In the Wireless Overview page you can see the general status of the Wifi connections and connected clients. You can also disable and edit the wifi from this page. Disable: Clicking this button will stop the Wifi access point. Tor and LAN will continue to work normally. This is good for if all you want is LAN and want to stop wifi from eating those precious air waves.
InvizBox User Guide | Version 1.3 InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 Device Configuration General Setup In this section you can see the status. You can also change the Channel and Transmission Power. Once you change any of these click the “ Save & Apply” b utton on the bottom of the screen Advanced Settings In this section you can edit the following : ● Band ● HT mode (802.
InvizBox User Guide | Version 1.3 Interface Configuration General Setup In this section you can edit the following : ● ESSID ● Mode ● Network ○ lan: VLAN Interface: "eth0.1" ○ tor: VLAN Interface: "eth0.3" ○ wan: VLAN Interface: "eth0.2" ○ wifi: VLAN Interface: "eth0.4" Wireless Network: Master "InvizBox" ● Hide ESSID ● WMM Mode It is advised only to change the E SSID. Once you change any of these click the “ Save & Apply” button on the bottom of the screen . InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 Wireless Security In this section you can edit the following : ● Encryption ● Cipher ● Key Once you change any of these click the “Save & Apply” button on the bottom of the screen InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 MacFilter In this section you can setup MAC based filter for wireless access point. Select the options you wish from ● None ● Allow Only Listed ● Allow All Except Listed In the dropdown “MACList” select the MAC that you want allowed or denied. Once you change any of these click the “ Save & Apply” b utton on the bottom of the screen Network The Network section allows you to go deeper and configure the wifi access point to your own setup.
InvizBox User Guide | Version 1.3 functionality of your InvizBox and you may need to do a hard reset. Tor In this section you can Restart Tor, Configure Proxy and Bridges, Select Exit Nodes and Advanced Config. It also shows you a general running status of Tor. Tor Status This page shows if the InvizBox is connected to the Tor network. It also shows the Tor version, current bandwidth and Tor circuit status.
InvizBox User Guide | Version 1.3 Bridge Configuration Bridges are Tor relays that help you circumvent censorship. Bridge relays (or "bridges" for short) are Tor relays that aren't listed in the main Tor directory. Since there is no complete public list of them, even if your ISP is filtering connections to all the known Tor relays, they probably won't be able to block all the bridges. If you suspect your access to the Tor network is being blocked, you may want to use bridges.
InvizBox User Guide | Version 1.3 These steps assume you have have a valid proxy of type HTTPS, SOCKS4, or SOCKS5. (To clarify, an HTTPS proxy is an HTTP proxy that also supports CONNECT requests.) 1. 2. 3. 4. Choose the Type of proxy you are using, whether HTTP/HTTPS, SOCKS4, or SOCKS5. Proxy IP Address: Enter the open proxy address. This can be a hostname or IP Address. Port: Enter the port for the proxy. Generally, you do not need a Username and Password.
InvizBox User Guide | Version 1.3 This option allow you to select from the list below and only use those selected Countries as exit Nodes 4. Do not use countries selected below This option allow you to select from the list below and it will exclude u sing those selected Countries as exit Nodes N.B From Tor Project We recommend you do not use these — they are intended for testing and may disappear in future versions.
InvizBox User Guide | Version 1.3 Notes: Changing this config will overwrite any changes you have made in the normal Tor Config section. Also be aware that an incorrect option here can break Tor and possibly affect your anonymity. Realtime graphs Load This shows the realtime load on the router for 1 min, 5 min and 15 min. Fairly self explanatory, but if not read more on load statistics h ere InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 Traffic To check the traffic flow on any of the interfaces WAN,Tor,LAN,Wifi etc. Open Realtime GRaphs > Traffic. It shows the Inbound/Outbound Average and Peak traffic rates. InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 Wireless The Wireless section show the realtime graphs for Signal, Noise and Physical Rate. InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 Connections This section gives an overview of all the currently active connections on the router both source and destination. InvizBox Ltd https://invizbox.
InvizBox User Guide | Version 1.3 Flash Periodically InvizBox will release a new firmware. This is the section where you upload and apply that firmware. Only ever flash official InvizBox firmware. We can’t assist if you start tinkering with other firmwares. Dont worry the flash procedure is pretty straightforward. To install a new firmware follow these simple steps 1. Download official firmware from our firmware page . 2. Take note of the listed “Checksum” on the InvizBox website. 3.
InvizBox User Guide | Version 1.3 Verify that the “Checksum” displayed matches the corresponding one on the firmware download page that you took note of earlier. I f they do not match click “Cancel”. I f everything matches then go ahead and click “Proceed”. Wait Approx 120 seconds for the flash to complete and for the InvizBox to reboot. That’s it. Note: All settings and any password changes will be erased / reset by flashing.
InvizBox User Guide | Version 1.3 Troubleshooting Reset Reserved for those moments when something bad has happened and you can’t figure it out. You’ve tried turning it off and on again. Hair is beginning to get pulled. Hard Reset is your friend. To perform a Hard Reset: 1. Power Off the Invizbox. 2. On the rear of the InvizBox there is a Reset button. (Use a paperclip or similar to push the button) 3. Hold the Reset button and Power on the InvizBox, Keep holding the Reset button for 30 seconds. 4.
InvizBox User Guide | Version 1.3 Misc Recommendations Please consider using the following plugins: ● HTTPS everywhere ● Privacy Badger ● uBlock Also please look into disabling WebRTC. This is an issue in both Firefox and Chrome which can lead to IP address exposure. There are firewall rules in place in the latest InvizBox firmware to help protect you. To disable WebRTC in Firefox, enter about:config into the address bar, then set media.peerconnection.enabled to false (double click works).
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the followi ng two conditions: (1) this device may not cause harmful interference, and (2) this dev ice must accept any interference received, including interference that may cau se undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
