Operation Manual

24
• The complete drawer is made out of two parts. The
top is the holder for the multi-padholder and the
bottom is the coffee-outlet. To clean the two
thoroughly, you can take it apart.
• At the backside there is a clamp, holding the
holder
on the drawer. You can pull the clamp gently
backwards until you can pull the
holder upwards.
Remove the complete
holder from the drawer.
• To replace the
holder on the drawer, you should place
the supports at the front of the holder in the recesses
at the top of the drawer. Than you can push back the
holder until the clamp snaps in place.
• Clean the separate parts: the
multi-padholder
13, the
cremamaker
14, the drawer 10,
the grid 7 and the driptray 8 with
warm water and some washing-up
liquid or in the dishwasher and
make sure that the parts are
dry before next use.
• Pay attention to clogging the
small drains in the middle of the padholder 13 and the
outside of the cremamaker 14. Remove the
cremamaker 14 by pushing it out, from below, with a
blunt object like a pen or the back of a teaspoon. This
also concerns the teamaker in the teapadholder 15.
• Check every day if the driptray 8 is empty and there
are no used coffeepads in the appliance. If the driptray
is full, it will overow and the liquid will ow under
the appliance.
We advise to descale your coffeepadmachine on a regular
bases. The period depends on the condition of your
water and the frequency of use. We advise to descale the
coffeepadmachine approx. every three months. You can
use a special descalingproduct for coffeemachines.
When you use a descalingproduct especially for
coffeemachines, you will have to follow the instructions
on the package of the descalingproduct accordingly.
• Switch off the coffeepadmachine with the on/off
button.
• Fill the reservoir according the instructions on the
package of the descalingproduct.
• Place a large mug or bowl under the coffee-outlet to
collect the descalingmixture.
• Open the drawer for the coffeepadholder by pulling the
handle on the side of the drawer outwards gently. The
drawer will now slide open.
• Place a new or used coffeepad in the multi-padholder
with the bulging side down and press it lightly. The
coffeepadmachine will be better descaled when you do
this and it cannot be clogged with descalingbits.
• Slide the drawer gently inwards until it can’t go further.
• Switch the coffeepadmachine on with the -button and
press
directly the 1-cup - button and 2-cups -
button at the same time. Do not let the machine heat
up.
• The coffeepadmachine will now rinse with the
CLEANING SEPARATE PARTS
8
10
13
14
7
DESCALING
descalingmixture.
• The coffeepadmachine will automatically switch itself
off when the rinsingprocess is ended. Repeat the
process until the waterreservoir is empty. After the
descaling you will have to rinse the machine upto
3 times with 1 liter of fresh cold water to make sure
that there is no descalingproduct left behind in the
coffeepadmachine to avoid a bad taste to the coffee.
Attention! If you haven’t used the coffeepadmachine for
a while, for instance if you have been away on a holiday,
you should remove all the separate parts for cleaning and
rinse the coffeepadmachine with fresh water. Place the
cleaned parts in the machine. This prevents an additional
taste.
When the appliance has a malfunction, one or two pilot
lamps will blink fast.
Lamp Color Condition Explanation
6.1/6.2 red/
green
constantly Coffeepadmachine is
ready for use.
6.1 red blinking
slowly
Appliance is heating
up.
6.1 red blinking
fast
Malfunction in the ap-
pliance, see the table
below.
6.2 green constantly Coffeepaddrawer is
locked correctly and
the appliance is ready
for making coffee.
6.2 green blinking
slowly
Don’t open the
drawer, it is still
locked. Please wait
a couple of seconds
until the pilot lamp
lights constantly.
6.2 off off Coffeepaddrawer is
not locked, open the
drawer and lock it
again.
Check the following steps to solve the malfunction
yourself.
Cause
Waterreservoir is not placed correctly
Solution
Empty the reservoir, ll it up again to the maximum-
level and place it on the coffeepadmachine.
Cause
Waterlevel is under the minimum
Solution
Fill the waterreservoir to the maximumlevel.
8 | SOLVING A MALFUNCTION