® Yes,you can.
CONTENTS Forward - Advisory Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Getting Acquainted With The Powerchair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features - Joystick Control Knob Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Seat and Backrest Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FOREWORD Important safety operating and maintenance instructions are contained in this user manual. We urge you to read and understand it before operating your power chair and refer to it as often as needed to help maintain safe use and all-round performance. ! All procedures involved should be practiced until you are familiar with them. However, if used improperly, it is possible for the wheelchair to become unstable.
GETTING ACQUAINTED WITH YOUR NEW POWER CHAIR Please ensure your dealer returns the WARRANTY REGISTRATION CARD. This will ensure your vehicle is covered for the relevant warranty periods against failures due to defects in manufacturing or materials. Please see the Owner’s Warranty Card supplied for full details. TRAINED RECOMMENDED ADJUSTMENTS TO BE CARRIED OUT BY A TRAINED AUTHORISED INVACARE DEALER ARE IDENTIFIED WITH THIS SYMBOL.
FEATURES Motor speed and direction are regulated by the joystick control unit. With practice, automatic control of acceleration, braking and change of direction will ensure a smooth, jerk-free ride. The variable speed selector gives you total control in any environment. The power chair cannot be driven when the batteries are being charged. Controller circuits are designed to prevent operation during the charging process. CHARGING • The battery gauge will indicate that your batteries are low.
SEAT AND BACKREST ADJUSTMENT ! Warning: It should be noted that under certain conditions, and configurations of the wheelchair, ie. for users with limited / no lateral body control, and with the backrest in the Creclined position, there is the potential to create a body trap between the armrest / sidepanel and the backrest. Suitable accessories are available from Invacare (lateral trunk supports_ to eliminate this risk. Before sitting in the chair, make sure it is NOT switched ON.
Armrest Adjustment The armrest can be pre-set for height by positioning the self-tapping screw (F) in one of the holes in the armrest tube. To adjust the height of each armrest, first release the locking lever (E) which clamps the arm tube, while holding onto the armrest. Move the armrest to the desired height position, re-tighten the locking wing screw (E).
TENSION ADJUSTABLE BACKREST TENSION ADJUSTABLE BACKREST The backrest upholstery tension can can be be adjusted adjusted to to achieve achieve the the comfort for for individual individual user user requirements. requirements. desired comfort To achieve achieve this, this, lift lift the the backrest backrest upholstery upholstery cover cover by by peeling peeling the the Velcro fastening individual tension Velcro fastening and and fold fold clear. clear.
HANDLING AND OPERATION - CONTROLLERS Your wheelchair is fitted with a programmable electronic controller that is very simple to operate. There are a selection of options, PILOT INTEGRAL, PILOT+ and the DYNAMIC DL. Whichever is selected will be most appropriate for your individual needs. The appearance varies, the function and driving characteristics are basically similar. The PILOT INTEGRAL is fitted as standard. The following instructions cover all types and available controller options.
DYNAMIC DL CONTROLLER When the ON/OFF button is pressed, a bleep tone can be heard from the controller and the battery charge indicator will light up confirming that power is switched on and the wheelchair is ready to move. The Speed Control Knob on the rear of the Controller enables you to reduce the maximum speed at which the wheelchair can travel when the joystick is fully deflected in any direction.
DX-REMG80I MASTER REMOTE Please read these instructions carefully before using the DX-REMG80I, and keep this leaflet safe for future reference. For Information: My Local wheelchair services representative is: ...................................................................... Based at ............................................ Telephone no:................................ Department: ..................................
Releasing the joystick and allowing it to return to the center position will bring the chair to a controlled stop. When you have finished driving, switch off by pressing and releasing the on/off switch. The fuel gauge on the top surface of the DX-REMG80I will have all 6 lights on, if your batteries are fully charged. As you use up the power by driving, the green lights and then the amber lights will go out. When only the red lights are left on, it is time to re-charge your batteries.
APPENDIX A CONTROLLING ACTUATORS (SEAT CONTROLS) OR LIGHTS USING THE JOYSTICK If your chair is fitted with Actuators (Seat Controls) or Lights they may be operated using the G80I’s joystick. To control actuators or lights using the joystick: Ensure the chair is stationary. Press the mode/speed selection button repeatedly until one of the non-driving mode symbols, shown below, appears on the 7 Segment Display.
PILOT+ The PILOT+ control system comprises of two or three modules - Joystick Module, Power Module and Actuator and Lighting Module (ALM). The ALM is only required if the optional Tilt-in-space or Powered Reclining Backrest are fitted. On/Off Switch and Battery Gauge The on/off switch applies power to the control system electronics, which in turn supply power to the wheelchair’s motors. Do not use the on/off power switch to stop the wheelchair unless there is an emergency.
JOYSTICK MODULE DETAILS JOYSTICK BATTERY CHARGING/ PROGRAMMING SOCKET COMMUNICATIONS CONNECTOR TO POWER MODULE Joystick Module without Lighting Joystick Module with Lighting CONTROLS ON/OFF SWITCH LIGHTS SWITCH AND LED BATTERY GAUGE LEFT TURN INDICATOR SWITCH AND LED MAXIMUM SPEED INDICATOR RIGHT TURN INDICATOR SWITCH AND LED MODE SWITCH HORN SWITCH HAZARD WARNING SWITCH AND LED ACTUATOR INDICATOR 13
Horn Switch The horn will sound whilst this switch is depressed. Lights Switch and LED To turn on the wheelchair’s lights operate this switch, the associated LED will illuminate. Left Turn Indicator Switch and LED To turn on the wheelchair’s left turn indicator operate this switch, the associated LED will flash at the same rate. If the LED flashes rapidly, one of the left turn indicator bulbs is defective, contact your authorised INVACARE dealer.
Maximum Speed Indicator This is a gauge that shows the maximum speed setting of the wheelchair. There are five speed settings: - step 1 is the lowest speed and step 5 is the highest speed Mode Switch - Speed Settings The mode switch is used to make the maximum speed changes and to change between wheelchair operation modes. If the mode switch is operated whilst you are driving the maximum speed setting will be increased by one step.
Speed Adjustment Mode When the control system is in this mode the maximum speed indicator will flash. The maximum speed can be adjusted by left or right movements of the joystick. Left will decrease the speed setting, right will increase it. Forward or reverse movements of the joystick will take you back into drive mode. FORWARD DECREASE SETTING INCREASE SETTING REVERSE Fig.
CONTROLLER OPTIONS The optional Attendant, Chin and Centre are fitted with the PILOT+ Control System. The display function is the same for each joystick module. DUAL/ATTENDANT CONTROL CAUTION: ATTENDANT, Before switching from Occupant Control to Attendant control, it is of the utmost importance that the speed control is checked and a safe manageable speed is selected before activating the joystick. Failure to do so may cause the chair to move uncontrollably, causing injury to the occupant or other people.
TRANSFERS Learning how to get in and out of a wheelchair safely and without injury is most important. Transferring to and from your powerchair may require practice and a good sense of balance. It is recommended that whenever possible you have assistance when transferring to and from your powerchair. It is recognised, however, that situations may occur when assistance is not available. It is desirable to learn and practice different techniques to accomplish a safe transfer.
FOOTRESTS REMOVAL - Standard Release winged screw A and slide the complete assembly from the seat frame. Ensure the winged screw is fully tightened when the footrest assembly is replaced. REMOVAL - Swing - Away Release the locking lever, swing footrest to the side, or lift up and off. Do this before sitting in the chair.
PUSHING THE CHAIR - FREEWHEEL MODE The power chair supplied is fitted with the lever dis-engage type motors. To dis-engage the drive to allow the chair to be pushed the following instructions should be followed carefully. To dis-engage the drive, operate the levers to the position A shown in the diagram. LEVERS POINTING OUTWARDS. To re-engage the drive, operate LEVERS POINTING REARWARDS. the levers to position B shown in the diagram.
OPERATING THE CHAIR OUTDOORS - KERB CLIMBING Always remember to use the safety belt when operating the chair outdoors. Ensure the footrests are locked in position. KERB CLIMBING - Centre Mounting It is important to follow the instructions detailed in ‘going up a kerb’ described below. (Please notethat thatleft leftororright righthand handare are REMOVAL: REMOVAL: (Please note identified as though being seated in the chair). identified as though being seated in the chair).
DIS-ASSEMBLY To enable the chair to be carried in the boot of most cars, follow these instructions: Step 1: Disconnect the Motor/Battery connector from the control box and remove the armrests. Release the locking lever. Step 2: Remove the calf strap from the footrests. This is simply attached by Velcro fastening. Remove the footrests completely by releasing the cam latch situated on the inside of the footrest frame hanger. CAUTION: Do not drive the chair with the footrests in the unlatched position.
DETACHABLE MOTORS For practical purposes and ease of operation, it is advisable to detach the motors as the last component of the chair to be dismantled and to re-attach first. PLEASE NOTE: Assistance may be required while this operation is carried out. Step 1: Unscrew the knurled locking knob A. This can be unscrewed completely and still be retained in position. Step 2: Release the side retaining pin B by turning it 180˚. Step 3: Unbolt clamp C on the vertical frame member.
DRIVE WHEEL REMOVAL To remove the rear drive wheels for puncture repairs carefully follow these instructions. Release the four bolts shown as A in the diagram. Check the tyres for wear, if excessive, replacement is recommended. The wheel is a split rim. It is important that the bolts securing the rims together are NOT released if the tyre is pneumatic and INFLATED. Upon reassembly tighten the fixing bolts securely. The wheel is alloy, do not over-tighten as this may damage the wheel rim.
TRANSPORTATION OF WHEELCHAIRS IN VEHICLES RECOMMENDED RESTRAINT METHODS For additional information, consult your authorised Supplier. For transportation purposes other than disassembly, the Spectra Plus may be used in vehicles which have been modified specifically for the purpose. The power chair must be secure using these recommended restraint methods. • • • • The power chairs are not designed or manufactured to be replacements for purpose built vehicle seating.
TRANSPORTATION CAUTION INVACARE always advises that a Powerchair secured in a vehicle will not provide the equivalent safety level and security as bespoke seating systems and recommends transfer to the vehicle seating, but also recognises that it is not always practical for the user to be transferred.
TRAY ASSEMBLY FITTING - OPERATION INSTRUCTIONS IMPORTANT: ENSURE THAT THE JOYSTICK CONTROL UNIT IS SWITCHED OFF BEFORE FITTING, REMOVING OR ADJUSTING THE TRAY ASSEMBLY. The tray assembly comes ready assembled and is designed to fit to either the left or right hand side of the wheelchair. The cut-out section is to accommodate the Joystick Control unit and determines which side the tray is fitted i.e.
LATERAL SUPPORT FITTING INSTRUCTIONS THE LATERAL SUPPORTS CAN ONLY BE FITTED TO THE FIRM UPHOLSTERED BACKREST ASSEMBLY (VISCOUNT SEATING). To attach the lateral supports to the back of the backrest assembly follow these instructions. Remove the existing pan-head screws from the top of each flange shown in Fig 1. Marked (A). The lower screws of each flange remain in place. Fig 1. Fig 2.
CHARGING BATTERIES The battery charger supplied with the wheel chair was developed to charge the batteries fitted to these products. Using alternatives will damage the batteries which are fitted as standard and invalidate the warranty on these components. The charger and electronic controller are designed to prevent the wheelchair operating during the charging process. Refer to the operating instructions supplied with the battery charger for a detailed description of the battery charging.
BATTERY CONNECTIONS The chair is fitted with two maintenance free „Gel“ batteries. For battery replacement we recommend to contact your authorised INVACARE dealer in order to ensure that replacement batteries are of the correct type and specifications, and that they are correctly installed and connected. A diagram showing the correct wiring connection is available on the inside of the front and rear battery box lid.
KEEPING YOUR CHAIR IN GOOD CONDITION Your powerchair will benefit from periodic inspection, adjustment and replacement of worn parts. Regular maintenance will enhance:• • • • • Reliable performance. Safety. Extended battery life. Confidence in operation. Low operating costs. You can help keep your chair in good condition by following a simple guide to home maintenance. CHROME/PAINTWORK This should be dried after contact with moisture. Clean once a month with a good quality auto-wax.
CONTROLLER AND CHARGER Servicing of the controller and charger should only be carried out by your local approved dealer. Do not attempt to open the units. Broken seals will invalidate the warranty. BRAKES WE STRONGLY RECOMMEND EVERY 6 MONTHS TO CHECK THE FUNCTION OF THE ELECTRONIC BRAKES AND WHEEL - LOCKS ADJUSTMENT. ( THIS SERVICE MAY NOT BE FREE OF CHARGE ). MOTORS The motors are fitted with long life brushes.
SPECTRA PLUS TECHNICAL INFORMATION DIMENSIONS: Seat Width: Overall Width: Overall Length: Height: Total Weight: Battery Weight: Maximum Carrying Capacity: Tyre Size - Front Tyre Size - Rear Maximum Permissible Incline: Speed: 38cm - 46cm 55cm 100cm 89cm 70kg 30AH - 11.7kg 40 AH - 14.8kg 18stone (114.
APPROVED ACCESSORIES AVAILABLE Puncture Proof Tyres Tray Detachable, powered reclining backrest Elevating Legrests Joystick knob options. PLEASE KEEP A NOTE OF THE DATE OF PURCHASE AND SERIAL NUMBER OF YOUR POWER CHAIR. PLEASE QUOTE THIS NUMBER IN ALL CORRESPONDENCE AND SERVICE REQUESTS. SERIAL NO. DATE OF PURCHASE: As with all powered motor vehicles we recommend that you take out maintenance insurance cover for out of warranty service requirements.
® WARRANTY STATEMENT GENERAL CONDITIONS OF LIMITED WARRANTY POWERED PRODUCTS MODELS COVERED: SPECTRA PLUS Invacare will repair or replace, at our option, to the original purchaser, free of charge, any part found upon receipt and examination by an authorised representative of Invacare to be defective in material and/or workmanship. 36 MONTHS WARRANTY - Items covered for thirty six months from the date of purchase.
® European Headquarter: Invacare International Sàrl, Route de Cité-Ouest 2, CH-1196 Gland Tel: (41) (0)22 354 60 10, Fax: (41) (0)22 354 60 11 hqeurope@invacare.com Sales Units: Belgium & Luxemburg: Invacare nv, Autobaan 22, B-8210 Loppem Tel: (32) (0)50 83 10 10 Fax: (32) (0)50 83 10 11 belgium@invacare.com Danmark: Invacare AIS, Sdr. Ringvej 39, DK-2605 Brøndby Tel: (45) (0)36 90 00 00 Fax: (45) (0)36 90 00 01 denmark@invacare.
