Product Manual

ManualsBrandsInvacare ManualsMobilityTop End Pro Basketball Wheelchair

SECTION 5—WHEELS

Part No 1122172 45 Everyday Series Wheelchairs/Sport Series Wheelchairs

Adjusting the Axle Tube

 WARNING

QUICK RELEASE LEVERS - Make sure the quick release levers are in the closed position before

using the wheelchair, otherwise injury or damage to the wheelchair may occur.

STANDARD and suspension camber clamps - Make sure the hex screws are securely tightened

before using the wheelchair, otherwise injury or damage to the wheelchair may occur.

CAUTION

ADJUSTABLE CAMBER SYSTEM ONLY - DO NOT close the quick-release levers or tighten the

hex screws without camber inserts in the axle tube. Damage to the axle tube will occur.

NOTE:Standbehindthewheelchairtodetermineleftorright.

Camber Tube With Single Camber

NOTE:Forthisprocedure,refertoFIGURE 5.20.

1. Ifnecessary,openbothcamberclamps.Referto

Opening/ClosingCamberClamps

onpage 34.

2. UsinganʺLʺsquare,rotate theaxletubeuntiltheflat

edgeofthecambertubeisata90°anglewiththe

ground/floorasshowninFIGURE 5.20.

3. Closebothcamberclamps.RefertoReferto

Opening/ClosingCamberClamps

onpage 34.

4. Determinethetoein/toeoutofthewheelchair.Referto

DeterminingToeIn/ToeOut

onpage 36.

FIGURE 5.20 Adjusting the Axle Tube - Camber Tube

With Single Camber

Adjustable Camber System

NOTE:Forthisprocedure,refertoFIGURE 5.21onpage46.

NOTE:Beforeperformingthisprocedure,makesure thecamberinsertsarepositionedtothelowestdegreeofcamber.RefertoAdjusting

RearWheelCamberonpage 35.

1. Ifnecessary,openbothcamberclamps.RefertoOpening/ClosingCamberClamps

onpage 34.

2. Loosenthesetscrewthatsecureseachtoeadjustmentringtotheaxletube(FIGURE 5.2 1).

3. UsinganʺLʺsquare,rotate theaxletubeuntiltheflatedgeofthecamberinsertisata90°anglewiththeground/floor

asshowninFIGURE 5.21.

4. Closetherightcamberclamp.Referto

Opening/Closing CamberClampsonpage 34.

5. RotatetheLefttoeadjustmentringuntilthetabstopsagainsttheLowermetaltabonthecamberclamp.

6. Securelytightensetscrewonlefttoeadjustmentring.

7. Measurethedistancebetweenthecenterlinesattherearandfrontoftherearwheelsatapproximately12inches(30.48

cm)

fromtheground/floor.RefertoDeterminingToeIn/ToeOutonpage 36.

8. Performoneofthefollowing:

•ToeIn/ToeOutMeasurementisWithin±1/8‐inch(.32cm)‐Proceedtostep9.

•ToeIn/ToeOutMeasurementisNotWithin±1/8‐inch(.32cm)‐Repeatsteps1‐7untiltoein/toeout measurementis

within±1/8inch.

9. Opentherightcamberclamp.Referto

Opening/ClosingCamberClampsonpage 34.

10. Repositionthecamberinsertstothehighestdegreeofcamber.RefertoAdjustingRearWheelCamber

onpage 35.

11. RepeatSTEP3.

Ground/

Floor

90° Angle

Place “L” Square Here

Flat Edge of

Camber Tube