Installation Manual
Table Of Contents
- Revisions
- Reasons of change
- Introduction
- Regulations
- General installation guidelines
- (RF exposure)
- Compliance boundary definition
- Table of Contents
- 1. Introduction
- Scope of document
- Target Audience
- Reference manuals
- Conventions
- 2. Prior to Installation
- Topics
- Packing list materials
- Powering materials
- Power injectors
- Power cables
- Power modules & connectors
- Grounding materials
- Data traffic materials
- S-FTP cables
- Fiber optic cables
- SFP
- Pole fastening materials
- Mounting bracket
- Steel hose clamps
- Cable ties
- StreetNodeTM 6250 PTP(1)
- Outdoor DC PonE
- Outdoor AC PonE
- Indoor AC PoE
- Anchor point
- / /
- Introduction
- Site survey
- Preparation of the installation premises
- Network port distributors
- Cables routing (lamp post)
- Power cable routing
- Cable conduits
- Wall installation
- Installation location
- Lamp post or pole
- Grounding
- Outdoor grounding system
- Power supply source
- Circuit breakers
- Line Of Sight (LOS) verification
- Lightning & Surge protection
- Internal ovp(2)
- Safety
- Introduction
- Cable length restrictions
- Instruction
- Topics
- Equipment installation tools
- Ethernet cable termination tools
- Power supply cable termination tools
- Grounding cable termination tools
- 3. Installation of StreetNode 6250 PTP
- Mechanical Installation & Grounding
- Installation of Traffic Cable(s)
- Installation of Power Cable (Direct Powering)
- Installation of Power Injector (Power over Ethernet)
- Appendix A: Terminating Ethernet (S-FTP) Cable
- Appendix B: Terminating Power Supply Cable
- Appendix C: Terminating Grounding cable
- Appendix D: Removing StreetNode 6250 PTP
- Appendix E: Standards of Compliance
- Precautions
- Topics
- Tools and materials
- Lamp post (or pole) installation procedure
- Grounding cable installation procedure
- Topics
- Tools and materials
- Ethernet (S-FTP) cable installation procedure
- Ethernet (S-FTP) cable installation with SFP
- Ethernet (S-FTP) cable installation with SFP
- Topics
- Tools and materials
- Procedure
- Introduction
- Topics
- Tools and materials
- Mechanical and cabling installation (PonE)
- Cabling installation (PoE)
- Introduction
- Parts of RG-45 jack
- Termination procedure
- Procedure
- Topics
- Procedure
Chapter 2. Prior to Installation
28
Site Prerequisites, Continued
Power supply
source
For the installation location, we assume the existence of an appropriate
power supply source with the following specifications:
StreetNode
TM
6250 PTP with DC power supply module:
-40.5 V dc to -60 V dc.
StreetNode
TM
6250 PTP with AC Power Supply Module:
90-240 V / 50 Hz to 60 Hz (Live / Neutral).
For applicable input voltage ranges for power injectors please refer to Power
injectors on page 6.
Circuit
breakers
The following table provides the circuit breakers characteristics for powering
of StreetNode
TM
6250 PTP and power injectors:
Powering Type
Required Circuit Breaker
Direct AC powering
• single-pole MCB 6 A
• 230 V AC (voltage rating)
• C-curve (for Industrial Applications)
Direct DC powering
• single-pole MCB 6 A
• min 72 V DC (voltage rating)
• C-curve (for Industrial Applications)
Powering via outdoor AC PonE
• single-pole MCB 6 A
• 230 V AC (voltage rating)
• C-curve (for Industrial Applications)
Powering via indoor AC PoE
• single-pole MCB 6 A
• 230 V AC (voltage rating)
• C-curve (for Industrial Applications)
Powering via outdoor DC PonE
• single-pole MCB 6 A
• min 72 V DC (voltage rating)
•
C-curve (for Industrial Applications)
Continued on next page