Installation Manual
Table Of Contents
- Revisions
- Reasons of change
- Introduction
- Regulations
- General installation guidelines
- (RF exposure)
- Compliance boundary definition
- Table of Contents
- 1. Introduction
- Scope of document
- Target Audience
- Reference manuals
- Conventions
- 2. Prior to Installation
- Topics
- Packing list materials
- Powering materials
- Power injectors
- Power cables
- Power modules & connectors
- Grounding materials
- Data traffic materials
- S-FTP cables
- Fiber optic cables
- SFP
- Pole fastening materials
- Mounting bracket
- Steel hose clamps
- Cable ties
- StreetNodeTM 6250 PTP(1)
- Outdoor DC PonE
- Outdoor AC PonE
- Indoor AC PoE
- Anchor point
- / /
- Introduction
- Site survey
- Preparation of the installation premises
- Network port distributors
- Cables routing (lamp post)
- Power cable routing
- Cable conduits
- Wall installation
- Installation location
- Lamp post or pole
- Grounding
- Outdoor grounding system
- Power supply source
- Circuit breakers
- Line Of Sight (LOS) verification
- Lightning & Surge protection
- Internal ovp(2)
- Safety
- Introduction
- Cable length restrictions
- Instruction
- Topics
- Equipment installation tools
- Ethernet cable termination tools
- Power supply cable termination tools
- Grounding cable termination tools
- 3. Installation of StreetNode 6250 PTP
- Mechanical Installation & Grounding
- Installation of Traffic Cable(s)
- Installation of Power Cable (Direct Powering)
- Installation of Power Injector (Power over Ethernet)
- Appendix A: Terminating Ethernet (S-FTP) Cable
- Appendix B: Terminating Power Supply Cable
- Appendix C: Terminating Grounding cable
- Appendix D: Removing StreetNode 6250 PTP
- Appendix E: Standards of Compliance
- Precautions
- Topics
- Tools and materials
- Lamp post (or pole) installation procedure
- Grounding cable installation procedure
- Topics
- Tools and materials
- Ethernet (S-FTP) cable installation procedure
- Ethernet (S-FTP) cable installation with SFP
- Ethernet (S-FTP) cable installation with SFP
- Topics
- Tools and materials
- Procedure
- Introduction
- Topics
- Tools and materials
- Mechanical and cabling installation (PonE)
- Cabling installation (PoE)
- Introduction
- Parts of RG-45 jack
- Termination procedure
- Procedure
- Topics
- Procedure
Chapter 2. Prior to Installation
16
Connections
StreetNode
TM
6250 PTP
(1)
The layout and description of the StreetNode 6250 PTP external elements
is given below:
With DC Power supply module
With AC Power supply module
#
Marking
Details
Use
A
GbE2
Ethernet
100/1000Base-T,
electrical (RJ-45).
Connection of Gigabit
Ethernet cable (traffic /
inband management /
PoE
(1)
input).
B
GbE1
Ethernet
100/1000Base-T,
electrical (RJ-45).
Connection of Gigabit
Ethernet cable (traffic /
inband management).
C
GbE3
Ethernet 1000Base-T
(SFP cage).
Installing a Gigabit
Ethernet SFP (optical or
electrical) for traffic /
inband management.
D1, D2
PSU
Power supply
receptacle with
protective cap.
Connecting the DC (D1) or
AC (D2) power supply
cable when StreetNode
6250 PTP is self-powered.
E
STAT
Multi-functioning LED
(Green / Red).
Providing system
indications during
operation.
F
GND
Enclosure grounding
terminal.
Connecting the outdoor
grounding cable.
Continued on next page
(1)
StreetNode
TM
6250 PTP radio can be powered by PoE / PonE only when fitted with the DC power
module.