Installation Manual
Table Of Contents
- Revisions
- Reasons of change
- Introduction
- Regulations
- General installation guidelines
- (RF exposure)
- Compliance boundary definition
- Table of Contents
- 1. Introduction
- Scope of document
- Target Audience
- Reference manuals
- Conventions
- 2. Prior to Installation
- Topics
- Packing list materials
- Powering materials
- Power injectors
- Power cables
- Power modules & connectors
- Grounding materials
- Data traffic materials
- S-FTP cables
- Fiber optic cables
- SFP
- Pole fastening materials
- Mounting bracket
- Steel hose clamps
- Cable ties
- StreetNodeTM 6250 PTP(1)
- Outdoor DC PonE
- Outdoor AC PonE
- Indoor AC PoE
- Anchor point
- / /
- Introduction
- Site survey
- Preparation of the installation premises
- Network port distributors
- Cables routing (lamp post)
- Power cable routing
- Cable conduits
- Wall installation
- Installation location
- Lamp post or pole
- Grounding
- Outdoor grounding system
- Power supply source
- Circuit breakers
- Line Of Sight (LOS) verification
- Lightning & Surge protection
- Internal ovp(2)
- Safety
- Introduction
- Cable length restrictions
- Instruction
- Topics
- Equipment installation tools
- Ethernet cable termination tools
- Power supply cable termination tools
- Grounding cable termination tools
- 3. Installation of StreetNode 6250 PTP
- Mechanical Installation & Grounding
- Installation of Traffic Cable(s)
- Installation of Power Cable (Direct Powering)
- Installation of Power Injector (Power over Ethernet)
- Appendix A: Terminating Ethernet (S-FTP) Cable
- Appendix B: Terminating Power Supply Cable
- Appendix C: Terminating Grounding cable
- Appendix D: Removing StreetNode 6250 PTP
- Appendix E: Standards of Compliance
- Precautions
- Topics
- Tools and materials
- Lamp post (or pole) installation procedure
- Grounding cable installation procedure
- Topics
- Tools and materials
- Ethernet (S-FTP) cable installation procedure
- Ethernet (S-FTP) cable installation with SFP
- Ethernet (S-FTP) cable installation with SFP
- Topics
- Tools and materials
- Procedure
- Introduction
- Topics
- Tools and materials
- Mechanical and cabling installation (PonE)
- Cabling installation (PoE)
- Introduction
- Parts of RG-45 jack
- Termination procedure
- Procedure
- Topics
- Procedure
StreetNode™ 6250 PTP
Installation & Cabling Manual - Edition 2.1
11
List of Materials, Continued
S-FTP cables
The following table shows the S-FTP cables, accessories and kits:
Item
Order Code / Photo
Description
A
ETH-CAB-SFTP
Ethernet cable S-FTP, 4x2xAWG24, CAT5e,
shielded, BLK, UV-rated (per meter).
B
ST-RJ45
RJ-45 connector, shielded, for S-FTP cable
termination.
C
ETH-HOOD
Gland for RJ-45 connector, IP67 class.
(1)
D
CRIMP-TOOL-S
Hand crimping tool for RJ-45 connector (ST-RJ45
order code).
E
RELAY-CAB
S-FTP Ethernet cable, 50 cm, both ends
terminated with RJ-45 connectors (2 x ST-RJ45)
& glands (2 x ETH-HOOD)
(used to interconnect two radio units in relay
application).
Limited quantities for use in trials.
F
ST-SMC-CAB
50 cm, one end terminated with RJ-45 connector
(1 x ST-RJ45) & gland (1 x ETH-HOOD)
(used to connect the radio unit to SMC (Small
Cell).
Limited quantities for use in trials.
Continued on next page
(1)
For equipping 2 x RJ-45 GbE interfaces per radio unit, an additional gland for RJ-45 connector needs
to be ordered as the radio equipment package includes only one gland.