User's Manual
Table Of Contents
- Revisions
- Reasons of change
- Introduction
- Regulations
- General installation guidelines
- (RF exposure)
- Compliance boundary definition
- Table of Contents
- 1. Introduction
- Scope of document
- Target Audience
- Reference manuals
- Conventions
- 2. Prior to Installation
- Topics
- Packing list materials
- Powering materials
- Power injectors
- Power cables
- Power modules & connectors
- Grounding materials
- Data traffic materials
- S-FTP cables
- Fiber optic cables
- SFP
- Pole fastening materials
- Mounting bracket
- Steel hose clamps
- Cable ties
- StreetNodeTM 6250 PTP(1)
- Outdoor DC PonE
- Outdoor AC PonE
- Indoor AC PoE
- Anchor point
- / /
- Introduction
- Site survey
- Preparation of the installation premises
- Network port distributors
- Cables routing (lamp post)
- Power cable routing
- Cable conduits
- Wall installation
- Installation location
- Lamp post or pole
- Grounding
- Outdoor grounding system
- Power supply source
- Circuit breakers
- Line Of Sight (LOS) verification
- Lightning & Surge protection
- Internal ovp(2)
- Safety
- Introduction
- Cable length restrictions
- Instruction
- Topics
- Equipment installation tools
- Ethernet cable termination tools
- Power supply cable termination tools
- Grounding cable termination tools
- 3. Installation of StreetNode 6250 PTP
- Mechanical Installation & Grounding
- Installation of Traffic Cable(s)
- Installation of Power Cable (Direct Powering)
- Installation of Power Injector (Power over Ethernet)
- Appendix A: Terminating Ethernet (S-FTP) Cable
- Appendix B: Terminating Power Supply Cable
- Appendix C: Terminating Grounding cable
- Appendix D: Removing StreetNode 6250 PTP
- Appendix E: Standards of Compliance
- Precautions
- Topics
- Tools and materials
- Lamp post (or pole) installation procedure
- Grounding cable installation procedure
- Topics
- Tools and materials
- Ethernet (S-FTP) cable installation procedure
- Ethernet (S-FTP) cable installation with SFP
- Ethernet (S-FTP) cable installation with SFP
- Topics
- Tools and materials
- Procedure
- Introduction
- Topics
- Tools and materials
- Mechanical and cabling installation (PonE)
- Cabling installation (PoE)
- Introduction
- Parts of RG-45 jack
- Termination procedure
- Procedure
- Topics
- Procedure
Chapter 2. Prior to Installation
38
Recommended Tools
Topics
This paragraph describes the following tools that will be needed:
• Equipment installation tools.
• Ethernet cable termination tools.
• Power supply cable termination tools.
• Grounding cable termination tools.
The tools are not supplied and are installer responsibility to be available
during installation.
Equipment
installation
tools
Item Tool/ Photo Description
1
Electrical screwdriver with
extension and allen bits:
• 3 mm (with internal safety pin)
• 7 mm (2 Nm)
• 8 mm (2 Nm / 4.2 Nm)
2
Adjustable torque spanners:
R.8 (2 Nm / 4.2 Nm)
R.28 (2 Nm)
3
PH-2cross headed screwdriver.
4
Flat-headed screwdriver.
5
Drill machine with appropriate:
• 8 mm bit (for StreetNode
TM
6250
PTP wall mounting).
• 5 mm bit (for PonE wall
installation).
• Hole cutter metal
(1)
(for
StreetNode
TM
6250 PTP lamp post
installation)
6
Tamper-proof torx screwdriver T10
Continued on next page
(1)
The hole diameter should be defined by the local regulations regarding outdoor electrical installations. For passing
all cables (1 x power, 2 x Ethernet, 1 x Fiber Optic and 1 x Grounding) 5 cm to 7 cm hole is required.