Datasheet
2
FN2853.7
September 4, 2015
Absolute Maximum Ratings Thermal Information
Supply Voltage V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . V- -0.3V to V+ +0.3V
Package Dissipation, T
A
+25°C . . . . . . . . . . . . . . . . . . . . . . .500mW
Operating Conditions
ICL7667C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to +70°C
Supply Voltages: V+ = +4.5V to +15V; V- = Ground to -15V
Logic Inputs: Logic Low = V- < Vin < 0.8V ; Logic High = 2.0V< Vin <
V+
Thermal Resistance (Typical, Note 1, 2)
JA
(°C/W)
JC
(°C/W)
8 Ld PDIP Package . . . . . . . . . . . . . . . 150 N/A
8 Ld SOIC Package . . . . . . . . . . . . . . . 170 N/A
Maximum Storage Temperature Range . . . . . . . . . . . -65° to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1.
JA
is measured with the component mounted on an evaluation PC board in free air.
2. For
JC
, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Parameters with MIN and/or MAX limits are 100% tested at +25°C, V+ = 0V unless otherwise specified.
Temperature limits established by characterization and are not production tested.
PARAMETER SYMBOL TEST CONDITIONS
ICL7667C, M ICL7667M
UNITS
T
A
= +25°C 0°C T
A
+70°C
MIN TYP MAX MIN TYP MAX
DC SPECIFICATIONS
Logic 1 Input Voltage V
IH
V+ = 4.5V 2.0 - - 2.0 - - V
Logic 1 Input Voltage V
IH
V+V+ = 15V 2.0 - - 2.0 - - V
Logic 0 Input Voltage V
IL
V+ = 4.5V - - 0.8 - - 0.5 V
Logic 0 Input Voltage V
IL
V+ = 15V - - 0.8 - - 0.5 V
Input Current I
IL
V+ = 15V, V
IN
= 0V and 15V -0.1 - 0.1 -0.1 - 0.1 µA
Output Voltage High V
OH
V+ = 4.5V and 15V V+
-0.05 V+ - V+
-0.1 V+ - V
Output Voltage Low V
OL
V+ = 4.5V and 15V - 0 0.05 - - 0.1 V
Output Resistance R
OUT
V
IN
= V
IL
, I
OUT
= -10mA, V+ = 15V - 7 10 - - 12
Output Resistance R
OUT
V
IN
= V
IH
, I
OUT
= 10mA, V+ = 15V - 8 12 - - 13
Power Supply Current I
CC
V+ = 15V, V
IN
= 3V both inputs - 5 7 - - 8 mA
Power Supply Current I
CC
V+ = 15V, V
IN
= 0V both inputs - 150 400 - - 400 µA
SWITCHING SPECIFICATIONS
Delay Time T
D2
(Figure 3) - 35 50 - - 60 ns
Rise Time T
R
(Figure 3) - 20 30 - - 40 ns
Fall Time T
F
(Figure 3) - 20 30 - - 40 ns
Delay Time T
D1
(Figure 3) - 20 30 - - 40 ns
ICL7667